Storage
Storage Safety
• Shut of f the engine, remove the key , and wait
for all moving parts to stop before you leave the
operator ’ s position. Allow the machine to cool
before adjusting, servicing, cleaning, or storing it.
• Do not store the machine or fuel near ames or
drain the fuel indoors or inside an enclosed trailer .
• Do not store the machine or fuel container where
there is an open ame, spark, or pilot light, such
as on a water heater or on other appliances.
Cleaning and Storage
1. Disengage the blade-control switch (PT O), and
engage the parking brake.
2. Shut of f the engine, remove the key , and wait
for all moving parts to stop before leaving the
operating position.
3. Remove grass clippings, dirt, and grime from the
external parts of the entire machine, especially
the engine and hydraulic system. Clean dirt and
chaf f from the outside of the engine cylinder
head ns and blower housing.
Important: Y ou can wash the machine with
mild detergent and water . Do not pressure
wash the machine. A void excessive use
of water , especially near the control panel,
engine, hydraulic pumps, and motors.
4. Check the parking brake operation; refer to
Adjusting the Parking Brake ( page 57 ) .
5. Service the air cleaner; refer to Servicing the Air
Cleaner ( page 42 ) .
6. Grease the machine; refer to Lubrication ( page
39 ) .
7. Change the crankcase oil; refer to Engine
Maintenance ( page 41 ) .
8. Check the tire pressure; refer to Checking the
T ire Pressure ( page 57 ) .
9. Change the hydraulic lters; refer to Changing
the Hydraulic Fluid and Filters ( page 63 ) .
10. Charge the battery; refer to Charging the Battery
( page 54 ) .
1 1. Scrape any heavy buildup of grass and dirt
from the underside of the mower , then wash the
mower with a garden hose.
Note: Run the machine with the blade-control
switch (PT O) engaged and the engine at high
idle for 2 to 5 minutes after washing.
12. Check the condition of the blades; refer to
Servicing the Cutting Blades ( page 66 ) .
13. Prepare the machine for storage when non-use
occurs over 30 days. Prepare the machine for
storage as follows:
A. Add a petroleum-based
stabilizer/conditioner to fuel in the
tank. Follow mixing instructions from
the stabilizer manufacturer . Do not use
an alcohol-based stabilizer (ethanol or
methanol).
Note: A fuel stabilizer/conditioner is most
ef fective when mixed with fresh fuel and
used at all times.
B. Run the engine to distribute conditioned fuel
through the fuel system for 5 minutes.
C. Shut of f the engine, allow it to cool, and
drain the fuel tank.
D. Start the engine and run it until it stops.
E. Dispose of fuel properly . Recycle the fuel
according to local codes.
Important: Do not store fuel containing
stabilizer/conditioner longer than
the duration recommended by the
fuel-stabilizer manufacturer .
14. Remove and check the condition of the spark
plug(s); refer to Engine Maintenance ( page 41 ) .
With the spark plug(s) removed from the engine,
pour 30 ml (2 tablespoons) of engine oil into the
spark plug hole. Use the starter to crank the
engine and distribute the oil inside the cylinder .
Install the spark plug(s). Do not install the wire
on the spark plug(s).
15. Check and tighten all bolts, nuts, and screws.
Repair or replace any part that is damaged.
16. Paint all scratched or bare metal surfaces. Paint
is available from your Authorized Service Dealer .
17. Store the machine in a clean, dry garage or
storage area. Remove the key from the switch
and keep it out of reach of children or other
unauthorized users. Cover the machine to
protect it and keep it clean.
73
To Next Page
Loading...
Need help?
General
