Index-2 Electrostatic Classifier Model 3082 and SMPS Spectrometer Model 3938
DMA field, 5-24
DMA lower bracket, 4-9
DMA not detected warning, 6-27
DMA voltage, 5-9, A-3
current setpoint, 5-9
DMA voltage field, 5-9
power button, 5-9
DMA voltage error, 6-27
DMA voltage self-check error, 6-27
DMA-voltage controller, 1-10
DMPS, B-1
DO commands, C-3
E
earth grounding label, ix
EEPROM. (see also memory chip)
electrical connector, 6-12
electrical safety, viii
Electrostatic Classifier
accessory kit, 2-2
advantages, 1-1
aerosol inlet, 4-6
applications, 1-2
back panel, 4-3
communication ports, 4-3
cooling fan, 4-3
power input module, 4-3
calibration screen, 5-39–5-49
cleaning impactor, 6-2
communication screen, 5-32
communications screen, 5-32
connecting to computer, 2-36
connecting to detector, 2-35
data export screen, 5-37
date and time screen, 5-28
description, 1-1, 4-1
device options screen, 5-27
diagnostic screen options, 5-31
diagnostics screen, 5-31
display
error messages, 5-5, 5-6
setup screen, 5-18
setup screen options, 5-18
status icons, 5-4
title bar. (see also title bar)
y-axis settings, 5-14
display screen, 5-29
error screen. (see also error
screen)
exporting data, 5-37
external control display, 5-51
flag assembly retaining screw, 2-7
front panel
touch-screen display, 4-2
front panel, 4-2
power button, 4-2
front panel
aerosol inlet, 4-2
gas reference screen, 5-27
gas tab screen, 5-26
history, B-1
how it works, 1-3
Electrostatic Classifier (continued)
impactor, 4-6
impactor theory, B-3
information screen, 5-30
installing flow equalizer assembly,
2-33
internal components, 4-5
circuit board, 4-5
cooling fan, 4-6, 4-10
filter manifold, 4-5
filters, 4-5
flow manifold, 4-6, 4-10
heat exchanger, 4-6, 4-10
high-voltage power supply, 4-5
main circuit board, 4-6, 4-10
power inlet module, 4-5
power supply, 4-6, 4-10
sheath flow blower, 4-5
lead shielding, 2-6
lifting warning, 2-1
logging data, 5-33
logging options screen, 5-34
maintenance, 6-1
moving, 3-1
operating, 5-2
operation, 5-1
overview, 1-1
packing list, 2-1
powering on, 2-38
product overview, 1-1
properties
hardware tab, 5-24
properties screen, 5-24, 5-25
properties tab, 5-19
removing cover, 6-8
schematic, 1-4
setup, 2-5
shipping, 3-1
shutoff, 5-53
side panel, 4-4
DMA base plate, 4-4
high-voltage socket, 4-4
neutralizer, 4-4
sheath flow port, 4-4
USB port, 4-4
theory of operation, B-1, B-5
unpacking, 2-1, 2-4
ventilation requirements, 2-4
x-axis settings, 5-12
enable logging, 5-34, 5-35
environmental conditions, A-4
equations
electrical mobility, B-11
equivalent length, B-20
error is encountered when setting
start at time, 6-29
error messages
data export, 5-38
error screen
error message, 5-5
wrench icon, 5-5
Ethernet communication, 2-37
Ethernet port, 4-9, 4-10
European recycling label, ix
export
data, 5-37
export data, 5-37
external control mode, 5-51
External control mode, 5-3
external control screen, 5-51
F
factory defaults, resetting, 5-48
filter direction of flow, 6-21
filter manifold, 6-9
firmware
upgrade, 6-25
firmware commands, C-2
description, C-3
list, C-3
flag assembly, 4-7
installation, 2-10
flag assembly O-ring
cleaning, 6-7
flow arrow, 6-10
flow controllers, 1-5
flow equalizer assembly, 1-11
installation, 2-33
flow field, 5-25
flow paths contributing to diffusion
losses, B-19
flow range for orifice size, 4-7
flow tab, 5-19
flowmeter
replacing, 6-11
front panel, 4-2
front panel display, A-3
G
gas
set properties, 5-26
gas reference screen, 5-27
gas tab, 5-26
get defaults for air, 5-27
graph cursor, 5-15
graph options, 5-11
greasing O-ring, 6-6
guide rod, 2-9
H
hardware configuration
detector, 5-25
DMA, 5-24
flow, 5-25
impactor, 5-24
neutralizer, 5-24
tube length, 5-25
hardware tab, 5-24
high impactor dP warning, 6-26
high impactor is difficult to insert, 6-28
high-voltage
warning, viii
high-voltage connection, 2-33
DMA, 2-33
To Next Page
Loading...
Need help?
General
