Index-1
I n d e x
0
0 to 3 percent mismatch between
particle diameter, 6-29
1
1nm-DMA, 1-1, 1-6, 1-8, 1-9, (see
also DMA)
accessory kit, 2-3
bypass flow, 2-30, 2-32, A-6
bypass flow plug, 2-30
cleaning Dacron screen, 6-20
cleaning electrodes, 6-15
cleaning/replacing screen, 6-20
connecting polydisperse flow, 2-31
flow manifold, 2-30
flow schematic, B-7
installation, 2-24, 2-28
installation (alternate), 2-30
maximum input concentration, A-6
measurements, A-6
particle size range, A-6
particle type, A-6
specifications, A-6
3
3088 maximum hours exceeded
warning, 6-27
3088 neutralization error, 6-27
A
advisory label, ix
aerosol flow, A-2, A-3
aerosol flow is negative, 6-28
aerosol inlet, 4-6, A-3
aerosol inlet flow range, 2-15
aerosol inlet temperature range, A-2
Aerosol Instrument Manager software
loses connection, 6-30
Aerosol Instrument software, 2-36
aerosol pressure range, A-2, A-3
aerosol temperature range, A-2, A-3
ambient operating conditions, A-4
approximate data transfer times, 5-38
argon
warning, viii
auto recovery, 5-52
B
back panel, 4-3
bipolar particle charge distribution in
air, B-8
blower current error, 6-26
butanol
safety, vii
warning, vii
bypass flow, 1-9, 2-30
C
calibration, 5-39, A-3
check, 5-42
impactor differential pressure, 5-45
impactor flow calibration, 5-46
restore defaults, 5-48
sheath flow, 5-39
sheath flow calibration, 5-39
user calibration, 5-39
calibration out of range warning
screen, 5-48
calibration screen, 5-39
cannot achieve desired aerosol flow
rate, 6-28
cannot connect from PC using USB,
6-28
cannot figure out how to change
particle density, 6-29
cannot find x-axis and y-axis settings
menus, 6-29
case temp error, 6-27
caution symbol, viii
change filters, 6-9
charger, A-2, A-3
charging theory, B-8
chemical safety, vii
circuit boards, 4-8
display PCB, 4-8
high-voltage PCB, 4-8
main PCB, 4-8
sensor PCB, 4-8
circular tube penetration efficiency,
B-18
classifier mode, 5-2, 5-7
classifier not powering on
automatically after shut-down, 6-28
classifier screen, 5-51
cleaning impactor, 6-2
cleaning solutions, recommended, 6-2
clear logged data, 5-38
clevis pin, 2-24, 2-26
communication ports, 4-9
computer
standby mode, 2-36
computer interface, C-1
connecting to computer, 2-36
CPC, 1-10
CPC inlet, 6-22
custom DMA
set up, 5-50
D
D50(nm) field, 5-21
data
logging, 5-34
data export, 5-37
data export error messages, 5-38
data logging error, 6-29
data logging icon, 5-4
date and time, 5-28
decimal symbol, 5-34
default reference values for gas
properties, B-12
DEG, vii
safety, vii
warning, vii
detector
connecting to classifier, 2-35
upgrading firmware, 2-35
detector field, 5-25
detector firmware not supported, 6-28
detector inlet flow error, 6-28
determination of P
1
, B-19
determination of P
2
, B-19
determination of P
3
, B-20
determination of P
4
, B-20
determination of P
5
, B-20
device options, 5-27
diagnostics, 5-31
diagnostics screen, 5-31
Diethylene glycol. (see also DEG)
Differential Mobility Analyzer, 1-3,
(see also DMA)
Differential Mobility Particle Sizer
(DMPS). (see also DMPS)
diffusion charge corrections, 5-4
diffusion correction icon, 5-4
diffusion loss
characterizing, B-18
importance, B-17
diffusion loss correction, B-17
digital I/O, 4-9, 4-10
options, 4-11
dimensions, A-3
DMA, 1-3
caution, 6-32
cleaning/changing Dacron screen,
6-18
custom setup, 5-50
high-voltage connection, 2-33
high-voltage connector, 2-33
installation, 2-24
ISO zero test, 6-22
warning, 2-33
DMA bracket, 2-24
To Next Page
Loading...
Need help?
General
