Unitech UT-101 User Manual

@
sales@utplindia.in
+91 7046223333 , 9427301436
www.utplindia.in
www
UT-101
UNIVERSAL PROCESS INDICATOR CONTROLLER&
3
Flame Proof
K : -50~1200˚C
R : 0~1750˚C
T : 0~400˚C
INPUT
RANGE
High scale / Low scale
Full range as per input selection
General
Specificaion
Power Supply
110/240V AC, 50Hz, 12/24VDC [Optional on demand]
Power Consumption
4 Watts Maximum
Operating Ambient
Temp. : 0~50˚C, Humidity : Below 90% Non condensing
Input
Type Of Input
T/C
K, J, R, S, T, E
RTD
Pt-100, Pt-1000, Cu-53 [2 wire, 3 wire]
Linear : 4 ~20mA DC, 0~20mA DC, 0 ~5 Amp AC
CURRENT [Analog]
VOLTAGE [Analog]
Linear : 0.5~2.5VDC, 1~5VDC, 0~10VDC
SPECIAL ON DEMAND
Linear : 0~75m/0~200mVDC, 0~100/200/300VDC
Indication
PV Indication
0.56” 4 DIGIT , 7 Segment Red Display in single row.
Relay Status
Front Red LED for all Relay Alarm status
RTD
Pt-100 : -50~400˚C
Linear All DC & AC : -1999~9999 Display
CURRENT [Analog]
VOLTAGE [Analog]
Linear All DC : -1999~9999 Display
SPECIAL ON DEMAND
Linear : -1999~9999 Display
T/C
Accuracy
T/C
+ 0.25% of Full Scale
RTD
Class A
+ 0.1% of Full Scale
ANALOG [V & I]
SPECIAL ON DEMAND
+ 0.1% of Full Scale
Automatic Software based self compensation
Cold Junction Comp.
“ ” or “ ” indication on displayOPEN OVER
Sensor Break Info.
AS per Input Range Table
Range Limits
>330 K for Voltage ,mV, and T/C, 100 R for current
Input Impedance
Status indication
Alarm modes
LEDs for Relay status & Communication
Low / High
Control Mode
On Off control
Dead Band controls
High and Low Set point for level application
Relay / SSR :Max. 2 Nos. :Max. 4 Nos. :Max. 2 Nos.[1]96X48 [2]96X96 [3]48X96
Relay Output
SSR [Volt] Output
Retransmission
24VDC @ 20 mA ,12VDC @ 20 mA
Linear : 0~20/ 4~20 mA DC, 0~10 VDC
NO-C-NC Contacts , 5A@240 VAC Resistive, up to 1 to 4 Relays as per size
Other Output
Transmitter Power Supply : Isolated 24VDC@30mA ,Max.
Output
Prog. parameters
Modbus RTU RS- 485/RS- 232 Communication
Baud rate, Parity, Node address, Stop bit
Protocols & method
Max. Connections
Communication
Up to 128 Units
Programmable
Parameters
Display resolution
Setpoint / Hysteresis
Relay logic
Full range as per input selection
-1999 to 9999 fully configurable for linear input
F.S. high & low alarm
Enclosure [If Reqd.]
FC-1 FC-2 :[1-Compartment] OR [2-Comp.] IIA, IIB Exter. keys & Cable Entries
TECHNICAL SPECIFICATIONS
INPUT RANGE
J : -50~750˚C,
S : 0~1750˚C,
E : -50~400˚C,
2.3 Technical Specifications

Unitech UT-101 Specifications

General

Brand	Unitech
Model	UT-101
Category	Controller
Language	English