Alpine CDE-W235EBT User Manual

*
e adjustment can also be made by pressing AUDIO/SETUP
(CDE-W235EBT only) or press AUDIO(CDE-W233E only). Refer
to “Adjusting Subwoofer Level/Bass Level/Middle Level/Treble
Level/ Balance (Between Le and Right)/Fader (Between Front and
Rear)/Loudness/Defeat” on page 11.
e output level of each source is individually adjustable. For example,
if the TUNER level sounds lower than CD, its output can be adjusted
without aecting the other sources.
e Hands free phone talk level, ring tone level and microphone gain
level can also be adjusted by using this setting (CDE-W235EBT only).
e High Pass Filter on this unit can be adjusted to suit your personal
taste.
e Low Pass Filter on this unit can be adjusted to suit your personal
taste.
e subwoofer output phase is toggled SUBWOOFER NORMAL (0°) or
SUBWOOFER REVERSE (180°). To adjust the level, turn the
Rotary encoder
.
When the subwoofer is on, you can adjust the subwoofer output level
(refer to “Adjusting Subwoofer Level/Bass Level/Middle Level/Treble
Level/Balance (Between Le and Right)/Fader (Between Front and
Rear)/Loudness/Defeat” on page 11).
When the subwoofer is on, you can select either SYS 1 or SYS 2 for the
desired subwoofer eect.
When an external amplier is connected, sound quality can be improved
by stopping the power supply of the built-in amplier.
Setting item: VOL LV ADJ
Setting item: HPF
Setting item: SUBW LPF
Setting item: SUBW PHASE
Setting item: SUBWOOFER
Setting item: SUBW SYS
Setting item: POWER IC
e
e
e
e
e
e
e
Further setting items: TUNER / DISC / USB / IPOD / BT AUDIO
*
/
AUX / PHONE TALK
*
/ RING TONE
*
/ MIC GAIN
*
Setting contents:
-5 dB ~ +5 dB
Setting contents:
HPF OFF (Initial setting) / HPF 60 (Hz) / HPF 80 (Hz) /
HPF 120 (Hz) / HPF 160 (Hz)
All frequencies above the selected cuto are output.
Setting contents:
LPF OFF (Initial setting) / LPF 60 (Hz) / LPF 80 (Hz) /
LPF 120 (Hz) / LPF 160 (Hz)
All frequencies lower than the selected cuto are output.
Setting contents:
NORMAL (Initial setting) / REVERSE
Setting contents:
SUBW OFF (Initial setting) / SUBW ON
SUBW OFF:
No subwoofer signal is output from the Subwoofer RCA Connectors
(refer to “Connections” on page 33).
SUBW ON:
The subwoofer signal is output from the Subwoofer RCA Connectors
(refer to “Connections” on page 33).
Setting contents:
SUBW SYS 1 / SUBW SYS 2 (Initial setting)
SUBW SYS 1:
Subwoofer level changes according to the main volume setting.
SUBW SYS 2:
Subwoofer level change is dierent from the main volume setting.
For example, even at low volume settings, the subwoofer is still
audible.
Setting contents:
OFF / ON (Initial setting)
OFF:
Use this mode when the line output of this unit is used to drive an
external amplier. In this setting, the head unit’s internal amplier is
turned OFF and cannot drive speakers.
ON:
The speakers are driven by the built-in amplier.
OFF:
ON:
Setting the Source Volume Level
Adjusting the High Pass Filter
Adjusting the Low Pass Filter
Setting the Subwoofer Phase
Turning Subwoofer ON/OFF
Setting the Subwoofer System
External Device
Connecting to an External Amplier (POWER IC)
•
Note
No sound is produced by the system when the power output is set to
OFF.
Amplier
Speakers
Front
left
Front
right
SPEAKER
RIGHT FRONT
SPEAKER
RIGHT REAR
SPEAKER
LEFT REAR
SPEAKER
LEFT FRONT
Rear
right
Rear
left
Front
left
Front
right
13
-EN
*
CDE-W235EBT only.

Alpine CDE-W235EBT Specifications

General

Brand	Alpine
Model	CDE-W235EBT
Category	Car Receiver
Language	English