EasyManuals Logo
Home>Cisco>Network Router>CRS-1 - Carrier Routing System Router

Cisco CRS-1 - Carrier Routing System Router Migration Guide

Cisco CRS-1 - Carrier Routing System Router
250 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #142 background imageLoading...
Page #142 background image
2-44
Cisco CRS-1 Carrier Routing System to Cisco CRS-3 Carrier Routing System Migration Guide
OL-13669-03
Chapter 2 Downgrading Your Cisco CRS-3 Carrier Routing System Router Back to a Cisco CRS-1 Carrier Routing
System Router
Downgrading your Cisco CRS-3 Carrier Routing System 4-Slot Line Card Chassis Back to a Cisco CRS-1 Carrier Routing
System 4-Slot Line Card Chassis
RP/0/RP0/CPU0:router#admin
RP/0/RP0/CPU0:router(admin)#config
RP/0/RP0/CPU0:router(admin-config)#controller fabric plane 0 shut
RP/0/RP0/CPU0:router(admin-config)#commit
Verify that fabric plane is now Admin-state Down.
RP/0/RP0/CPU0:router(admin)#show controllers fabric plane all
Plane Admin Oper up->dn up->mcast
Id State State counter counter
---------------------------------------------
0 DOWN DOWN 1 0
1 UP UP 0 0
2 UP UP 0 0
3 UP UP 0 0
4 UP UP 0 0
5 UP UP 0 0
6 UP UP 0 0
7 UP UP 0 0
Power Disable the Fabric Card
Next, we disable power to the Fabric node, and verify that node is moved to “UNPOWERED” state.
RP/0/RP0/CPU0:router#admin
RP/0/RP0/CPU0:router(admin)#config
RP/0/RP0/CPU0:router(admin-config)#hw-module power disable loc 0/SM0/SP
RP/0/RP0/CPU0:router(admin-config)#commit
RP/0/RP0/CPU0:router(admin)#show platform
Node Type PLIM State Config State
<snip>
0/SM0/SP FC-140G/S N/A UNPOWERED PWR,NSHUT,MON
0/SM1/SP FC-140G/S N/A IOS XR RUN PWR,NSHUT,MON
0/SM2/SP FC-140G/S N/A IOS XR RUN PWR,NSHUT,MON
0/SM3/SP FC-140G/S N/A IOS XR RUN PWR,NSHUT,MON
0/SM4/SP FC-140G/S N/A IOS XR RUN PWR,NSHUT,MON
0/SM5/SP FC-140G/S N/A IOS XR RUN PWR,NSHUT,MON
0/SM6/SP FC-140G/S N/A IOS XR RUN PWR,NSHUT,MON
0/SM7/SP FC-140G/S N/A IOS XR RUN PWR,NSHUT,MON
<snip>
Swap the Cisco CRS-3 Fabric with the Newly Installed Cisco CRS-1 Fabric
Now, physically remove the powered down Fabric node from slot 0/SM0 and replace it with the CRS-1
Fabric.
Physically Removing the CRS-3 Fabric Card
This section describes how to physically remove the CRS-3 fabric card, and verify that node is ready to
have a CRS-1 fabric card installed in its place.

Table of Contents

Other manuals for Cisco CRS-1 - Carrier Routing System Router

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco CRS-1 - Carrier Routing System Router and is the answer not in the manual?

Cisco CRS-1 - Carrier Routing System Router Specifications

General IconGeneral
BrandCisco
ModelCRS-1 - Carrier Routing System Router
CategoryNetwork Router
LanguageEnglish

Related product manuals