EasyManuals Logo
Home>Cisco>Network Router>CRS-1 - Carrier Routing System Router

Cisco CRS-1 - Carrier Routing System Router Migration Guide

Cisco CRS-1 - Carrier Routing System Router
250 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #154 background imageLoading...
Page #154 background image
2-56
Cisco CRS-1 Carrier Routing System to Cisco CRS-3 Carrier Routing System Migration Guide
OL-13669-03
Chapter 2 Downgrading Your Cisco CRS-3 Carrier Routing System Router Back to a Cisco CRS-1 Carrier Routing
System Router
Downgrading your Cisco CRS-3 Carrier Routing System 4-Slot Line Card Chassis Back to a Cisco CRS-1 Carrier Routing
System 4-Slot Line Card Chassis
Troubleshooting Tips
For troubleshooting information, see the documents described in the “Related Documents” section on
page 1-86.
Example
The following example shows commands to enable power to the newly installed CRS-3 Fabric Card:
RP/0/RP0/CPU0:router#admin
RP/0/RP0/CPU0:router(admin)#config
RP/0/RP0/CPU0:router(admin-config)#no hw-module power disable loc 0/SM0/SP
RP/0/RP0/CPU0:router(admin-config)#commit
Verify that power has been enabled to the Fabric Node (state is not UNPOWERED).
RP/0/RP0/CPU0:router(admin)#show platform
Node Type PLIM State Config State
<snip>
0/SM0/SP FC/S(SP) N/A PRESENT PWR,NSHUT,MON
0/SM1/SP FC-140G/S(SP) N/A IOS XR RUN PWR,NSHUT,MON
0/SM2/SP FC-140G/S(SP) N/A IOS XR RUN PWR,NSHUT,MON
0/SM3/SP FC-140G/S(SP) N/A IOS XR RUN PWR,NSHUT,MON
0/SM4/SP FC-140G/S(SP) N/A IOS XR RUN PWR,NSHUT,MON
0/SM5/SP FC-140G/S(SP) N/A IOS XR RUN PWR,NSHUT,MON
0/SM6/SP FC-140G/S(SP) N/A IOS XR RUN PWR,NSHUT,MON
0/SM7/SP FC-140G/S(SP) N/A IOS XR RUN PWR,NSHUT,MON
<snip>
Power-up the Newly Installed Cisco CRS-1 Fabric Card
We now enable power back to the new Fabric Node.
RP/0/RP0/CPU0:router#admin
RP/0/RP0/CPU0:router(admin)#config
RP/0/RP0/CPU0:router(admin-config)#no hw-module power disable loc 0/SM0/SP
RP/0/RP0/CPU0:router(admin-config)#commit
Verify that power has been enabled to the Fabric Node (state is not UNPOWERED).
RP/0/RP0/CPU0:router(admin)#show platform
Node Type PLIM State Config State
<snip>
0/SM0/SP FC/S(SP) N/A PRESENT PWR,NSHUT,MON
0/SM1/SP FC-140G/S(SP) N/A IOS XR RUN PWR,NSHUT,MON
0/SM2/SP FC-140G/S(SP) N/A IOS XR RUN PWR,NSHUT,MON
0/SM3/SP FC-140G/S(SP) N/A IOS XR RUN PWR,NSHUT,MON
0/SM4/SP FC-140G/S(SP) N/A IOS XR RUN PWR,NSHUT,MON
0/SM5/SP FC-140G/S(SP) N/A IOS XR RUN PWR,NSHUT,MON
0/SM6/SP FC-140G/S(SP) N/A IOS XR RUN PWR,NSHUT,MON
0/SM7/SP FC-140G/S(SP) N/A IOS XR RUN PWR,NSHUT,MON
<snip>

Table of Contents

Other manuals for Cisco CRS-1 - Carrier Routing System Router

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco CRS-1 - Carrier Routing System Router and is the answer not in the manual?

Cisco CRS-1 - Carrier Routing System Router Specifications

General IconGeneral
BrandCisco
ModelCRS-1 - Carrier Routing System Router
CategoryNetwork Router
LanguageEnglish

Related product manuals