Danfoss 5000 Flux Manual

171
MG.10.J4.02 – VLT is a registered Danfoss trade mark
VLT
®
5000 SyncPos option
Index
■■
■■
■ Index
Symbols
#DEBUG ............................................................. 123
#INCLUDE........................................................... 124
_GETVEL............................................................. 122
4-Setup ................................................................ 128
A
Abbreviation ......................................................... 131
About Program ...................................................... 57
About this manual ................................................... 6
ACC ....................................................................... 70
Acceleration feed-forward FFACC (37) .......... 33, 141
ACCMAXQC (10) .................................................. 135
Analog inputs ......................................................... 10
Analog outputs ...................................................... 10
APOS ..................................................................... 70
Arithmetic .............................................................. 65
Arrays ..................................................................... 64
Arrays versus Variables ....................................... 65
Reading and Writing Arrays ............................... 65
reset .................................................................... 50
Assignment Operation ........................................... 67
Autostart ................................................................ 46
Linking autostart programs ................................ 46
Repeated execution ........................................... 46
AVEL ...................................................................... 71
AXEND .................................................................. 71
Axis parameters ................................................... 129
Axis Process Data ................................................. 115
B
BANDWIDTH (35) .......................................... 33, 141
Before you begin ................................................... 22
C
Calling up macros ................................................. 41
Changes during operation ................................... 128
Colors Editor .......................................................... 55
COM_OPT ........................................................... 165
Command List ....................................................... 44
Command run times .............................................. 61
Command Structure .............................................. 61
Commands which have been extended ..............170
Communication Setup........................................... 26
COMOPTGET ........................................................ 72
COMOPTSEND ..................................................... 73
Compiler options ................................................... 55
Connection examples ............................................ 15
Constants ............................................................... 64
Context menu ........................................................ 41
Context-sensitive help ........................................... 57
CONTINUE ............................................................ 73
Controller menu ..................................................... 45
Autostart ............................................................. 46
Axis parameters.................................................. 47
Delete all programs ............................................ 46
Delete EEPROM ................................................ 50
Global parameters ............................................. 47
Parameter Name ................................................ 48
Parameters ......................................................... 47
Programs ............................................................ 45
Reset .................................................................. 50
Restore from file ................................................. 49
Save programs ................................................... 45
Save RAM ........................................................... 49
Start programs.................................................... 45
Conventions ............................................................. 7
Conversion index ................................................. 128
CPOS ..................................................................... 74
Cross-references ................................................... 57
CSTART.................................................................. 74
CSTOP ................................................................... 75
CVEL ..................................................................... 75
D
D.TIME CMP.ACT. 780 .........................................127
Dampening of vibrations ....................................... 35
Data sampling interval ........................................... 51
Data type ............................................................. 128
Dead time compensation .....................................127
DEC ....................................................................... 76
DEF ORIGIN ......................................................... 76
DEFMORIGIN ....................................................... 76
DELAY.................................................................... 77
Delete file .............................................................. 40
Derivative factor KDER (12) .......................... 32, 135
Determining the maximum velocity ....................... 36
Development menu ............................................... 42
Break and break all ........................................... 43
Command List .................................................... 44
Continue program .............................................. 43
Execute............................................................... 42
Execute now ....................................................... 44
Insert ................................................................... 44
Move to position ................................................. 44
Preparing single-step ......................................... 43
Select controller .......................................... 26, 43
Single-step ......................................................... 43
DFLTACC (34) ........................................................141
DFLTVEL (33) ....................................................... 140
Dialog fields ........................................................... 23
Digital inputs .............................................. 10, 11, 14
Digital outputs ........................................... 10, 11, 14
DIM ........................................................................ 78
DIM Statement ...................................................... 64

Danfoss 5000 Flux Specifications

General

Brand	Danfoss
Model	5000 Flux
Category	DC Drives
Language	English