Denon AVR-1911 User Manual

39
ENGLISH
Basic versionSimple version InformationAdvanced version
Playback in ZONE2 (Separate room)
• You can operate this unit so as to enjoy audio in a different room
(ZONE2) other than the MAIN ZONE (room where the unit is located).
• You can simultaneously play back the same source in both the MAIN
ZONE and ZONE2. You can also play back separate sources in the
MAIN ZONE and ZONE2.
Audio output
ZONE2 playback by speaker output
The ZONE2 audio signals are output from this unit’s SURR. BACK/
AMP ASSIGN speaker terminals using the amplifier assignment
function.
n Connecting and setting the speakers
“Amp Assign” setting
(vpage 54) and audio
signals output
Connecting the speakers
ZONE2
Output signal :
Stereo (L / R)
MAIN ZONE
ZONE2
This unit
We recommend using high quality pin-plug cables for audio
connections in order to prevent noise.
NOTE
It is not possible to play the digital audio signals input from the HDMI,
COAXIAL or OPTICAL connectors in ZONE2.
Playback
1
Switch ZONE SELECT to “ZONE2”.
The remote control unit switches to the
operating mode for ZONE2.
Input source
select buttons
2
Press AMP.
3
Press ZONE/DEVICE ON to turn
on the ZONE2 power.
The indicator on the display lights.
• Also, pressing any of input source select
button in standby mode turns on the power.
• When
ZONE/DEVICE OFF is pressed, ZONE2
turns off.
• Power in ZONE2 can be turned on or off by
pressing ZONE2 ON/OFF on the main unit.
4
Press the input source select button.
The audio signal of the selected source is output to ZONE2.
• Turn
SOURCE SELECT after
pressing ZONE2 SELECT on
the main unit to select an input
source.
When power for both MAIN ZONE and ZONE2 is set to ON, power of
the MAIN ZONE only can be turned off. Select “MAIN” in step 1 then
press ZONE/DEVICE OFF.
Adjusting the volume
Use VOL df to adjust the volume.
GAdjustable rangeH
– – – –80dB – –40dB – 18dB
(When the “Volume Display” (vpage59) setting is “Relative”)
GAdjustable rangeH
0 – 41 – 99
(When the “Volume Display” (vpage59) setting is “Absolute”)
• At the time of purchase, “Volume Limit” (vpage 58) is set to
“–10dB (71)”.
Turn MASTER VOLUME after pressing ZONE2 SELECT on the main
unit to adjust the sound volume.
Turning off the sound temporarily
Press MUTE.
The sound is reduced to the level set at “Mute Level” (vpage58) in
the menu.
• To cancel, either adjust the volume or press MUTE again.
• The setting is canceled when the zone’s power is turned off.

Denon AVR-1911 Specifications

General

Frequency range	10 - 100000 Hz
Audio output channels	7.1 channels
Audio A/D Converter (ADC)	24-bit/96kHz
Signal-to-Noise Ratio (SNR)	100 dB
Total Harmonic Distortion (THD)	0.8 %
HDMI	Yes
Audio system	Dolby TrueHD, Dolby Digital Plus, Dolby Digital EX, Dolby Pro Logic II, Dolby Pro Logic IIx, Dolby Pro Logic IIz, DTS-HD, DTS 96/24
Output power	125 W
Dimensions (WxDxH)	434 x 381 x 171 mm
Power requirements	AC 230, 50 Hz
HDMI ports quantity	5
AM band range	522 - 1611 kHz
FM band range	87.5 - 108 MHz
I/O ports	1 x Component in 1 x Composite Monitor out 1 x USB 1 x Microphone 1 x FM Tuner Antenna 1 x AM Tuner Antenna
Connectivity technology	Wired
Headphone outputs	7
Digital audio optical in	1
Product color	Black
Power consumption (standby)	0.1 W
Power consumption (typical)	460 W

Weight and Dimensions

Weight	10200 g