Digitax M1 mdt User Manual

The information contained here are property of DIGITAX Automotive Electronics Italy, and extremely confi dential. Any disclosure, copying, distribution to third
party
is strictly prohibited.
28
The Tariff
General Descrip on
Here follows an example of an easy tariff that uses two Blocks to calculate two diff erent tariff amounts.
In the subscribed example there are two tariff s that diff er for the ini al drop value distance (Parameter n. 11).
The Block 1 has been programmed with an Ini al Drop Value distance of 1000, the Block 2 with a value distance of 2000.
To pass from Block 1 to Block 2 must be pressed K1 bu on. To do it program the Parameter n. 13 of the Block n. 1 with a
value of 2 (se ng value of 2 means > go to Block 2 ).
To go back to Block 1, set in Parameter n. 13 of Block 2 the value of 1.
With this procedure it is possible to move from Block 1 to Block 2 and change the bander value by pressing K1 bu on.
- Power on the taximeter. By default all the parameters programmed in Block 0 get loaded in the Working Block.
- Press OP bu on to pass in Hired posi on. Now Block 1 gets loaded in the Working Block upda ng the changed param-
eters values (Parameter 11 = 0 > 11).
PS: The parameter 15 defi ne the start fare block. This is the block loaded when OP bu on is pressed to pass from For Hire
to Hired posi on.
Working
Block
Param.001
.
.
.
.
.
Param.429
Working
Block
Param.001
.
.
P.340
.
Param.429
Working
Block
Param.001
.
.
.
.
Param.429
Working
Block
Param.001
.
P.340*
.
Param.429
Block 0
Param.001
.
.
.
.
Param.429
Easy
Tariff
Amount
Power
On
Power
On
Power
On
Final
Tariff
Amount
Complex
Tariff
Amount
*= Modifi ed Parameter
Block 0
P.001.
.
.
.
P.015=1
.
.
.
Param.429
Wk.Block
P.001.
.
.
.
P.015=1
.
.
.
Param.429
Block 1
P.001.
.
P.011=1000
.
P.013=2
.
.
.
Param.429
Wk.Block
P.001.
.
P.011=1000
.
P.013=2
.
.
.
Param.429
Block 2
P.001.
.
P.011=2000
.
P.013=2
.
.
.
Param.429
Wk.Block
P.001.
.
P.011=2000
.
P.013=2
.
.
.
Param.429
The taximeter calculates the tariff thanks to the interac on of 429 programmable parameters.
They work into a block. The M1 MDT have 63 parameters blocks that can be programmed to generate even the most
complex tariff . Two blocks are very par cular: Block 0 and the Working
Block.
The Block 0 is the StartUp block that loads per default all the 429 pa-
rameters in the Working Block when the taximeter starts up. In
a simple tariff calcula on is suffi cient to use only the Block 0 to
calculate the amount.
The “Working Block” (not visible by the user) is the opera ve
block that makes the fi nal tariff calcula on.
In a simple tariff , it is ge ng charged by Block 0 with his 429
default programmed parameters. It calculates the fi nal amount.
To calculate a more complex tariff it is necessary
to use, in addi on to Block 0 , other programmed
blocks of parameters.
Their content replace, at the programmed event
(Prog.Date, Key press OP, K1, K2 etc.),
the relevant parameters of the Working Block.
Every new modifi ed parameter value in a Block
will replace the old one in the Working Block up-
da ng the tariff .
Example
For Hire Hired Hired

Digitax M1 mdt Specifications

General

Brand	Digitax
Model	M1 mdt
Category	Automobile Accessories
Language	English