The information contained here are property of DIGITAX Automotive Electronics Italy, and extremely confi dential. Any disclosure, copying, distribution to third
party
is strictly prohibited.
34
Programming Parameters
Here follows the complete list of F1 tariff parameters. They are 429 ques ons to the user.
Param.
Number
Func ons
Param.
Value
1
Index of displayed tariff
This is the number or le er to be displayed on the digit on the le hand-side of the secondary (small) display.
The display can show one of the following numbers or le ers either in normal mode or in blinking mode (add 16 to the chosen
value):
DISPLAY “0” “1” “2” “3” “4” “5” “6” “7” “8” “9” “A” “B” “C” “D” “E” “F”
NORMAL 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
BLINKING 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
Using the value 35 the display will not be used anymore for the tariff -index, but becomes available for other purposes. So, the
secondary display becomes one of 5 digits instead of 1 digit plus 4 digits.
TARIFF PARAMETERS
2
Distance of fi rst unit: the distance that corresponds with the fi rst unit of the fare. The distance is given in metres with an accuracy of 0.1 m.
The allowed value goes from 0.1 (min) to 6553.5 (max). The digit indica ng mul ples of 0.1 m (so at the right of the decimal point) will fl ash.
0.1 -
6553.5
metres
3
Distance of second unit: the distance that corresponds with the second unit of the fare.
If the second unit distance is the same as the fi rst unit distance then the second unit distance does not need to be given. Automa cally the fi rst
unit distance will be used. The distance is given in metres with an accuracy of 0.1 m. The allowed value goes from 0.1 (min) to 6553.5 (max).The
digit indica ng mul ples of 0.1 m (so at the right of the decimal point) will fl ash.
0.1 -
6553.5
metres
4
Distance of following units: the distance that corresponds with the third and higher units of the fare.
If the third and higher unit distance is the same as the second unit distance then the third and higher unit distance does not need to be given.
Automa cally the second unit distance will be used. The distance is given in metres with an accuracy of 0.1 m. The allowed value goes from 0.0
(min) to 6553.5 (max). The digit indica ng mul ples of 0.1 m (so at the right of the decimal point) will fl ash.
0.1 -
6553.5
metres
5
Wai ng- me of fi rst unit: the wai ng- me that corresponds with the fi rst unit of the fare. The wai ng- me is given in seconds with an accuracy
of 0.1 sec. The allowed value goes from 0.1 (min) to 6553.5 (max). The digit indica ng mul ples of 0.1 sec. (so at the right of the decimal point)
will fl ash.
0.1 -
6553.5
seconds
6
Wai ng- me of second unit: the wai ng- me that corresponds with the second unit of the fare.
If the second unit wai ng- me is the same as the fi rst unit wai ng- me then the second unit wai ng- me does not need to be given.
Automa cally the fi rst unit wai ng- me will be used. The wai ng- me is given in seconds with an accuracy of 0.1 sec.
The allowed value goes from 0.1 (min) to 6553.5 (max). The digit indica ng mul ples of 0.1 sec. (so at the right of the decimal point) will fl ash.
0.1 -
6553.5
seconds
7
Wai ng- me of following units: the wai ng- me that corresponds with the third and higher units of the fare.
If the third and higher unit wai ng- me is the same as the second unit wai ng- me then the third and higher unit wai ng- me does not need to
be given. Automa cally the second unit wai ng- me will be used. The wai ng- me is given in seconds with an accuracy of 0.1 sec. The allowed
value goes from 0.1 (min) to 6553.5 (max). The digit indica ng mul ples of 0.1 sec. (so at the right of the decimal point) will fl ash.
0.1 -
6553.5
seconds
8
Cost of fi rst unit: the cost that corresponds with the fi rst unit of the far
e. The cost is given in the local currency with an accuracy of 1. The
allowed value goes from 0 (min) to 65535 (max). See Q.273 and Q.274 for adding a fi xed decimal point.
0 - 65535
To Next Page
Loading...
Need help?
General
