Emerson ControlWave Series User Manual

Emerson FB2200 Flow Computer Instruction Manual
D301784X012
March 2019
116 Index
1-7. Removing Fiberglas Enclose Cap and Latch .... 10
1-8. Potential Locations for Tamper-evident Tape . 11
2-1. Dimensions – Multivariable Sensor Version -
Fiberglass Enclosure ......................................... 13
2-2. Dimensions – Multivariable Sensor Version
Aluminum Enclosure ......................................... 14
2-3. Dimensions – No Integral Sensor Version –
Fiberglass Enclosure ......................................... 15
2-4. Dimensions – No Integral Sensor Version –
Aluminum Enclosure ......................................... 16
2-5. Dimensions – Static Pressure Sensor Version –
Fiberglass Enclosure ......................................... 17
2-6. Dimensions – Static Pressure Sensor Version –
Aluminum Enclosure ......................................... 18
2-7. Grounding Stud ............................................. 19
2-8. Fiberglass Enclosure Fasteners ....................... 20
2-9. Aluminum Enclosure Clamps ......................... 20
2-10. Transmitter with Coplanar Flange ................ 21
2-11. Transmitter with Coplanar Flange and
Optional Flange Adapters ................................. 21
2-12. Transmitter with Traditional Flange and
Optional Flange Adapters ................................. 21
2-13. Proper Bolt Installation ................................ 22
2-14. O-rings with Flange Adapters ...................... 23
2-15. Aluminum Enclosure Pole Mounting ............ 24
2-16. Fiberglass Enclosure Pole Mounting ............. 25
2-17. Aluminum Enclosure Panel or Wall Mounting
......................................................................... 26
2-18. Attaching mounting tabs ............................ 27
2-19. Fiberglass Enclosure Panel or Wall Mounting28
2-20. Housing Rotation Set Screw ........................ 29
2-21. Module Power Control ................................. 33
2-22. DC Power Connections ................................ 34
2-23. Removing Plastic Tabs from Battery Pack ..... 35
2-24. Captive Fastening Screws ............................ 36
2-25. Rotate Assembly Forward ............................ 37
2-26. Connect the Battery .................................... 38
2-27. Removing Termination Cover of Internal Solar
Regulator ......................................................... 39
2-28. Battery Strap ............................................... 39
2-29. Easing Battery Pack into Compartment ....... 40
2-30. Battery Pack Attached to Compartment ...... 40
2-31. Battery Pack Attached to Compartment ...... 41
2-32. Battery Pack Attached to Compartment ...... 42
2-33. Battery pack attached to compartment ....... 45
2-34. Removing Fork Connectors ......................... 45
2-35. Wiring Solar Power ...................................... 45
2-36. Wiring Solar Power ...................................... 46
2-37. Routing Battery Wires ................................. 46
2-38. Wiring Solar Power ..................................... 47
2-39. Wiring Solar Power-Internal ........................ 48
2-40. Installing 30W Solar Panel ........................... 50
2-41. 30W Solar Panel Installed ............................ 51
2-42. Adjusting the 30W Solar Panel Tilt Angle .... 52
2-43. Connecting a Device to COM1
Using RS-232 ................................................... 53
2-44. Connecting a Device to COM1
Using RS-422 ................................................... 54
2-45. Connecting a Device to COM1
Using RS-485 ................................................... 55
2-46. Connecting a Device to COM2 or
COM3 Using RS-232 ......................................... 56
2-47. Connecting a Device to COM2 or
COM3 Using RS-485 ......................................... 57
2-48. Connecting to Ethernet .............................. 58
2-49. Ethernet jumper ......................................... 59
2-50. Wiring the Door Contact Terminal .............. 60
2-51. Board Info Screen in FBxConnect ................ 60
3-1. Base I/O (AI/AO 1 & 2, DI/DO/PI 1 & 2 ............ 62
3-2. Wiring for 8-channel Expansion I/O Module
& 6-channel Expansion I/O Module ................... 63
3-3. AI Wiring - Base I/O (AI/AO & AI/AO2 only) .... 65
3-4. AI Wiring for 8-channel Expansion I/O
Module & 6-channel Expansion I/O Module ...... 66
3-5. AO Wiring - Base I/O (AI/AO2 & AI/AO2) ........ 67
3-6. AO Wiring - 8-channel Expansion I/O Module
and 6-channel Expansion I/O Module ............... 68
3-7. DI Wiring - Base I/O
(DI/DO/PI1 & DI/DO/PI2) .................................. 69
3-8. DI Wiring - 8-channel Expansion I/O
Module & 6-channel Expansion I/O Module ...... 70
3-9. DO Wiring - Base I/O ..................................... 71
3-10. DO Wiring - 8-channel Expansion I/O
Module and 6-channel Expansion I/O Module ... 72
3-11. PI Wiring - Base I/O ..................................... 74
3-12. PI Wiring - 8-channel I/O Module and
6-channel I/O Module ...................................... 74
3-13. RTD/PRT Wiring for 2-Wire ......................... 75
3-14. RTD/PRT Wiring for 3-Wire ......................... 75
3-15. RTD/PRT Wiring for 4-Wire ......................... 76
3-16. Connecting a 4088B Transmitter for a
Second Meter Run ........................................... 77
3-17. Relay Wired to Isolated DO ......................... 78
3-18. Relay Wired to Non-Isolated DO ................. 79
3-19. Radio Wiring ............................................... 79
4-1. Waking up the Display .................................. 84

Emerson ControlWave Series Specifications

General

Brand	Emerson
Model	ControlWave Series
Category	Desktop
Language	English