Epson TM-m30II User Manual

16
Chapter 1 Product Overview
Panel LED
Power LED
• Lights when the power supply is on.
• Off when the power supply is off.
• Flashes during the network to start up, when waiting for power off, or updating firmware.
Error LED
• Lights or flashes when an error occurs. (For information about the flashing patterns, see "Status and Errors"
on page 19.)
• Ligh
ts after the power is turned on or after a reset (offline). Automatically goes out after a while to indicate
that the printer is ready.
• Off when the printer is in standard mode (online).
Paper LED
• Lights when the roll paper is out.
• Flashes to urge user to operate the Feed button.
Wi-Fi LED
• Lights while the printer is connected to Wi-Fi.
• Off while the printer is not connected to Wi-Fi or while the printer is connected to a wired LAN.
• Flashes while communication is temporarily disabled because an IP address has not been acquired or for
other reason.
Ethernet LED
• Lights while the printer is connected to Ethernet.
• Off while the printer is not connected to Ethernet or while the printer is connected to Wi-Fi.
• Flashes while communication is temporarily disabled because an IP address has not been acquired or for
other reason.
Bluetooth LED
• Lights while the printer is connected via Bluetooth.
• Off while the printer is not connected via Bl uetooth.
• Flashes while the printer is waiting to be paired with another device.
Do not turn on by using the power switch while waiting for the power to turn off (when the Power
LED is flashing). Otherwise, it may not startup correctly.
This LED also lights if you have enabled the "Roll-paper near-end detection" function and the near-
end status is detected.
For more details, see "Software Settings" on page 47.
This func
tion can be used only with a 80-mm width roll paper and only when the printer has been
set up to eject printed paper from the front side. For more details about the restrictions, see
"Enabling the Roll Paper Near-End Detection" on page 46.

Epson TM-m30II Specifications

General

Type	POS printer
Character sets	ANK
Print technology	Direct thermal
Maximum resolution	203 x 203 DPI
Maximum roll diameter	83 mm
Supported paper width	58 mm - 80 mm (Breite) mm
Maximum printing width	80 mm
Power plug type	Type G
Power source type	AC
USB port	Yes
USB connector	USB Type-A / USB Type-B
USB 2.0 ports quantity	2
Connectivity technology	Wired
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	5 - 45 °C
Operating relative humidity (H-H)	10 - 90 %
Wi-Fi	No
Internal memory	- MB
Built-in barcodes	-
Country of origin	Philippines
Mounting position	Horizontal/Vertical
Autocutter durability	1.5 million cuts
Built-in sensors details	Paper End Sensor, Papier-Sensor
Sound pressure level (printing)	55 dB
Mean time between failures (MTBF)	360000 h
Product color	White
Print head life	150.000.000 Impulse
Mean cycles between failures (MCBF)	65000000
Pre-installed software	TMNet WebConfig, ePOS-Device, ePOS-Display, ePOS-Print
Package depth	240 mm
Package width	200 mm
Package weight	2150 g
Quantity per pack	1 pc(s)
Quantity per pallet	128 pc(s)
Quantity per pallet (UK)	192 pc(s)
Master (outer) case width	400 mm
Master (outer) case height	255 mm
Master (outer) case length	490 mm
Master (outer) case weight	0 g
Harmonized System (HS) code	84433210
Quantity per master (outer) case	4 pc(s)

Weight and Dimensions

Width	127 mm