Haier HLP24E Service Manual

Chapter. 6 MAINTENANCE SERVICE AND TROUBLE SHOOTING
Order No. TL1001S003V0
Rev.
Service Manual
Issue
15
When using the child lock function,
if the top cover is opened, the
machine will stop and display E2
alarm. After 15 minutes the machine
will automatic drainage
clear the E2 alarm, please close the top
cover and press the START/PAUSE ”
button. Then E2 alarm will be cleared.
Phenomena The reason How to settle
ThedigitrondisplaysE0. Thetoplidisopenduring
reserve procedure.
Closethetoplid.
Ɣ
Thedrainagecannot
work, or is too slow. The
digitron displays E1.
Is the drain hose put down?
Is the drain hose blocked?
Put down the drain hose . Open and
Clean the foreign material. Open and
Ɣ
Ɣ
close the top lid once.
close the top lid once.
It stops running in
midway. The digitron
displays E2.
Thetoplidisnotclosed.
Closethetoplid.Ɣ
Ɣ
Thesafetyswitchacts,
and the spinning cannot
work. The digitron
displays E3.
Are the laundries put slantingly?
Is the machine slanting?
Reorder the laundries. Close the top lid.Ɣ
Place the machine horizontally, open
and close the top lid once.
Ɣ
not work, or is slow, the
digitron displays E4.
Is the water tap opened, or is
there water supply failure?
Is the water inlet valve blocked?
Isthewaterpressuretoolow?
Open the water tap. Open and close theƔ
top lid once.
Clean the water inlet valve then openƔ
and close the top lid once.
Use after the water pressure is normal.
Ɣ
ThedigitrondisplaysE6. Thewaterlevelsensorisbad. Pleasecontacttheafter-salesservice
Ɣ
department.
The
machine
does not
act
Notwash Istherepowerfailure?
Is the power plug inserted tightly?
Isthewaterlevelreachedpreset
position?
PleaseuseitwhentherespowerƔ
supply.
Insert the power plug tightly.Ɣ
Fill water to the preset position.
Ɣ
Not spin
Is the power plug inserted tightly?
Isthetoplidclosedreliably?
Insert the power plug tightly.Ɣ
Closethetoplid.Ɣ
Ɣ
The water tap leaks
There is abnormal sound
inside the machine
Is the screw of the jointer of water
inlet hose loose or awry?
Is the machine slanting?
Are the laundries put slantingly in
spinning?
Are there any foreign materials?
Fasten the screw of the jointer properly.
Ɣ
Adjust the machine to be even
Reorder t he laundries and close the top
lid.
Remove the foreign materials.Ɣ
Ɣ
Ɣ
Phenomena Explanation
Thespinningisintermittentwhenitstarts. Balancethelaundriesto avoidslanting.
Push the spin” button to select Spin”, but it doesn t
work.
Theprogramissettingthedraintime.Sometimeis
needed before it starts spinning.
There may be some water flowing out of the drain hose
in the first use of the machine.
The wash procedure is paused .
It is the water remained in the factory inspection of
performance.
The cloth sensor is checking the cloth, it will add
water after 48 seconds.
The pulsator pauses during water inlet in wash
and rinse.
It is to avoid splashing during water inlet.
When the power plug is inserted,computer board
indicatorisswitchedon,andthemachinestarts
working.
It is the special resume function. In the case of power
failureorthepowerplugislooseduringwashing,the
machine can save the running program, and resume
theprogramafterthepowersupplyisrecovered.You
do not need to set the program again.

Haier HLP24E Specifications

General

Door hinge	Up
Drum volume	42.4 L
Control type	Buttons
Display type	LED
Loading type	Top-load
Drum material	Stainless steel
Product color	White
Built-in display	Yes
Appliance placement	Freestanding
AC input voltage	120 V
AC input frequency	60 Hz
Energy consumption washing per cycle	- kWh
Drum capacity	- kg
Spin-drying class	-
Maximum spin speed	800 RPM
Noise level (spin)	- dB
Load balancing system	No
Number of washing programs	3

Weight and Dimensions

Depth	510 mm
Width	500 mm
Height	901.7 mm
Weight	19504 g