EasyManuals Logo
Home>HIKVISION>Network Hardware>DS-7104NI-Q1

HIKVISION DS-7104NI-Q1 User Manual

HIKVISION DS-7104NI-Q1
93 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #57 background imageLoading...
Page #57 background image
Figure 6-7 NAT
2. Turn on Enable.
3. Select Mapping Type as Manual or Auto
Auto The port mapping items are read-only, and the external ports are set by the router
automacally. You can click Refresh to get the latest status of the port mapping.
Manual Select an external port type. Click to edit External Port. You can use the default
external port No., or change it according to actual requirements. External Port
indicates the port No. for port mapping in the router.
The value of the RTSP port No. should be 554 or between 1024 and 65535, while
the value of the other ports should be between 1 and 65535 and the value must
be
dierent from each other. If mulple devices are congured for the UPnP™
sengs under the same router, the value of the port No. for each device should
be unique.
4. Set the virtual server of your router, including internal source port, external source port, etc.
The virtual server parameters shall be corresponding with your device port.
6.2.4 Ports (More
Sengs)
Set dierent port types to enable relevant funcons as your desire.
Go to Conguraon → Network → General → More Sengs .
Alarm Host IP/Port
The device will send the alarm event or
excepon message to the alarm host when an alarm is
triggered. The remote alarm host must have the client management system (CMS) soware
installed.
Alarm Host IP refers to the IP address of the remote PC on which the CMS soware (e.g.,
iVMS-4200) is installed, and the Alarm Host Port (7200 by default) must be the same as the
alarm monitoring port
congured in the soware.
Server Port
For remote client soware access. Ranges from 2000 to 65535. The default value is 8000.
HTTP Port
Network Video Recorder User Manual
43

Table of Contents

Other manuals for HIKVISION DS-7104NI-Q1

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the HIKVISION DS-7104NI-Q1 and is the answer not in the manual?

HIKVISION DS-7104NI-Q1 Specifications

General IconGeneral
CertificationFCC 15 B, ANSI C63.4-2014 CE EN50130-4, EN 61000-3-2, EN 61000-3-3
Product colorBlack
Output current1 A
Output voltage48 V
Power consumption (typical)10 W
Total Power over Ethernet (PoE) budget36 W
Operating temperature (T-T)-10 - 55 °C
Operating relative humidity (H-H)10 - 90 %
HDD capacity0 GB
HDD interfaceSATA, SATA II, SATA III
Maximum storage capacity6 TB
Number of HDDs installed0
Number of HDDs supported1
Networking standardsIEEE 802.3af, IEEE 802.3at
USB 2.0 ports quantity2
Ethernet LAN data rates10, 100 Mbit/s
Power over Ethernet (PoE)Yes
Ethernet LAN (RJ-45) ports5
Supported network protocolsTCP/IP, DHCP, Hik-Connect, DNS, DDNS, NTP, SADP, SMTP, UPnP
Power over Ethernet (PoE) ports quantity4
Video codecsH.265+/H.265/ H.264+/H.264
Input bandwidth40 Mbit/s
Output bandwidth60 Mbit/s
Maximum resolution1920 x 1080 pixels
Video input channels4 channels
Supported resolutions1920 × 1080, 1600 × 1200, 1280 × 1024, 1280 × 720, 1024 × 768
Wi-FiNo
Weight and Dimensions IconWeight and Dimensions
Depth225 mm
Width265 mm
Height48 mm
Weight1000 g

Related product manuals