Honeywell NOTIFIER PSE-10 User Manual

18 PSE Series Instruction Manual — P/N LS10227-000NF-E:B 3/29/2021
Installation Cascading Multiple Units
2.8 Cascading Multiple Units
Up to four PSE power supplies can be cascaded together to provide additional NAC extenders for a system. Maintain separation of
power-limited and non-power-limited wiring as shown in Figure 2.6 on page 15.
Figures 2.11 and 2.12 show the controlling signal connected to Input 1 of PSE1. However, typically any available Input of PSE1 can be
used.
Figures 2.11 and 2.12 show NAC7 of PSE1 - PSE3 as the cascading output. However, any available Output of PSE1 – PSE3 can be used.
The following notes apply to Figure 2.11.
1. Set all PSE units to Slave (sync follower) mode.
2. The debounce/dejitter setting must be set to 1 msec on all cascaded units. See Table 3.3 on page 23.
3. Any output used for remote sync applications cannot have notification appliances installed on the same circuit.
4. Notification appliances cannot be installed on the interconnecting control circuits.
5. The total line impedance for interconnected units cannot be such that it creates a voltage drop > 3.2 VDC.
6. Ground fault supervision is provided via the general trouble relay for domestic and export models and via the dedicated ground
fault relay in the Canadian models. Enable ground fault detection on PSE1 and disable detection on PSE2-4 with negative (-)
battery terminals tied together. FACP ground fault supervision will be independent of cascaded PSE1-4. (FACP negative battery
terminal is not tied to PSE1).
The following notes apply to Figure 2.12.
1. Set PSE1 to Master Mode, and the desired strobe/horn type. Set remaining PSE units to Slave (sync follower) mode.
2. The debounce/dejitter setting must be set to 1 msec on PSE2 – PSE4 units. See Table 3.3 on page 23.
3. Strobe/Horn devices connected to the PSE units are not guaranteed to be in sync with FACP devices when using this configuration
4. Any output used for remote sync applications cannot have notification appliances installed on the same circuit.
5. Notification appliances cannot be installed on the interconnecting control circuits.
6. The total line impedance for interconnected units cannot be such that it creates a voltage drop > 3.2 VDC.
7. Ground fault supervision is provided via the general trouble relay for domestic and export models and via the dedicated ground
fault relay in the Canadian models. Enable ground fault detection on PSE1 and disable detection on PSE2-4 with negative (-)
battery terminals tied together. FACP ground fault supervision will be independent of cascaded PSE1-4. (FACP negative battery
terminal is not tied to PSE1).
NOTE: Any mode of operation that requires an additional control signal (i.e. a trigger signal), such as Selective Silence or Sync Mode, will
affect which Inputs may be available on PSE1 for use with cascading. (Triggers signals are usually assigned to Input 2.) Refer to those
sections of the manual for specifics.
NO NC C NO NC C NO NC C
TB4
TB15
T
B
3
T
B
2
T
B
1
T
B
1
3
O
U
T
6
T
B
1
2
O
U
T
5
T
B
1
1
O
U
T
4
T
B
1
0
O
U
T
3
T
B
9
O
U
T
2
T
B
8
O
U
T
1
NO NC C NO NC C NO NC C
TB4
TB15
T
B
3
T
B
2
T
B
1
T
B
1
3
O
U
T
6
T
B
1
2
O
U
T
5
T
B
1
1
O
U
T
4
T
B
1
0
O
U
T
3
T
B
9
O
U
T
2
T
B
8
O
U
T
1
NO NC C NO NC C NO NC C
TB4
TB15
T
B
3
T
B
2
T
B
1
T
B
1
3
O
U
T
6
T
B
1
2
O
U
T
5
T
B
1
1
O
U
T
4
T
B
1
0
O
U
T
3
T
B
9
O
U
T
2
T
B
8
O
U
T
1
NO NC C
NO NC C
NO NC C
TB4
TB15
T
B
3
T
B
2
T
B
1
T
B
1
3
O
U
T
6
T
B
1
2
O
U
T
5
T
B
1
1
O
U
T
4
T
B
1
0
O
U
T
3
T
B
9
O
U
T
2
T
B
8
O
U
T
1
FACP
NAC or remote
sync output
Figure 2.11 System Sync Connections Triggered by FACP
PSE1
PSE2
PSE3
PSE4PSE4
NO NC C NO NC C NO NC C
TB4
TB15
T
B
3
T
B
2
T
B
1
T
B
1
3
O
U
T
6
T
B
1
2
O
U
T
5
T
B
1
1
O
U
T
4
T
B
1
0
O
U
T
3
T
B
9
O
U
T
2
T
B
8
O
U
T
1
NO NC C NO NC C NO NC C
TB4
TB15
T
B
3
T
B
2
T
B
1
T
B
1
3
O
U
T
6
T
B
1
2
O
U
T
5
T
B
1
1
O
U
T
4
T
B
1
0
O
U
T
3
T
B
9
O
U
T
2
T
B
8
O
U
T
1
NO NC C NO NC C NO NC C
TB4
TB15
T
B
3
T
B
2
T
B
1
T
B
1
3
O
U
T
6
T
B
1
2
O
U
T
5
T
B
1
1
O
U
T
4
T
B
1
0
O
U
T
3
T
B
9
O
U
T
2
T
B
8
O
U
T
1
NO NC C
NO NC C
NO NC C
TB4
TB15
T
B
3
T
B
2
T
B
1
T
B
1
3
O
U
T
6
T
B
1
2
O
U
T
5
T
B
1
1
O
U
T
4
T
B
1
0
O
U
T
3
T
B
9
O
U
T
2
T
B
8
O
U
T
1
FACP
SLC
Figure 2.12 System Sync Connections Triggered by Control Module
Control
Module
Regulated
24VDC
UL864 listed
power supply
PSE1
PSE2
PSE3
PSE4

Honeywell NOTIFIER PSE-10 Specifications

General

Brand	Honeywell
Model	NOTIFIER PSE-10
Category	Extender
Language	English