JVC MX-D302T User Manual

11
Three Ways to Select a Station ——————————————
o Press the TUNING DOWN or TUNING UP on the MULTI CONTROL repeatedly to move from
frequency to frequency until you find the one you want. (Manual Tuning).
OR
o Press and hold the TUNING DOWN or TUNING UP on the MULTI CONTROL for a few seconds,
the frequency starts changing on the display. When a station is tuned in, the frequency stops changing.
(Auto Tuning).
OR
o Possible only after presetting stations.
Press once and release the P. DOWN or P. UP on the MULTI CONTROL to go to the next preset
station.
You can also use the Remote Control to tune in preset channels:
1. Press the FM/AM button so that you can receive the most recent station tuned in.
2. Select the station by entering the preset number in the number keys of the Remote Control.
• Example: for channel 5, press 5. For channel 15, press +10 then 5. For channel 20, press +10,
then 10. For channel 30, press +10 twice then 10.
• After you have selected the preset number and the number is displayed, the broadcast frequency
of the selected channel is displayed.
Presetting Stations
You can preset up to 30 FM stations and up to 15 AM stations for the preset numbers.
Note: In some cases, test frequencies have been already memorized for the tuner since the factory
examined the tuner preset function before shipment. This is not a malfunction. You can preset the stations
you want into memory by following the presetting method.
1. Select a band by pressing the FM/AM button.
2. Press the TUNING DOWN or TUNING UP on the MULTI CONTROL to
tune into a station.
3. Press and hold the number keys on the Remote Control for a few
seconds to set the preset number.
For preset numbers 1 to 10:
Press the number key for the preset number you want to set.
For preset numbers 11 to 20:
Press the 1 to 10 buttons after pressing the +10 button.
For preset numbers 21 to 30:
Press the 1 to 10 buttons after pressing the +10 button twice.
The preset number appears in the display after you have pressed the number keys. If you press and
hold the button, the preset number display blinks. Release the button after the number starts to blink.
This completes the preset setting.
4. Repeat steps 1 to 3 for each station you want to store in memory
with a preset number.
CAUTION: If the Unit is unplugged or if a power failure occurs, the preset
stations will be erased in a few days. If this happens, preset the station
again.
Changing the FM Reception Mode
When an FM stereo broadcast is hard to receive or noisy, press the FM MODE button on the Remote
Control so that the MONO indicator lights up in the display. Reception improves, but there is no stereo
effect.
To restore the stereo effect, press the FM MODE button on the Remote Control so that the MONO
indicator goes off. In this stereo mode, the ST indicator lights up and you can hear stereo effects, when a
program is broadcast in stereo.
1
23
456
7
8
9
10
10
CLOCK TIMER
SET
– SELECT +
1
2
3
FM/AM
or
FM MODE
EN.MX-D302T[J]/f 98.1.16, 11:05 AM11

JVC MX-D302T Specifications

Amplifier Section

output power	55 watts per channel
input sensitivity	300 mV
input impedance	50 kohms

Cassette Deck Section

frequency response Type II	50 - 14, 000 Hz
frequency response Type I	50 - 14, 000 Hz
wow and flutter	0.15% (WRMS)

CD Automatic Changer Section

cd capacity	3 discs
dynamic range	85 dB
signal-to-noise ratio	90 dB

Tuner Section

fm tuning range	87.5 - 108.0 MHz
am tuning range	530 - 1, 710 kHz
dimensions	265 × 315 × 340 mm

Speaker Specifications

tweeter size	5 cm
woofer size	12 cm
power handling capacity	60 W

Power Specifications

power requirements	AC 120 V, 60 Hz
power consumption	95 watts
standby power consumption	9 watts

Weight and Dimensions

dimensions	265 × 315 × 340 mm
mass	7.2 kg
speaker dimensions	215 × 315 × 230 mm