Mahindra Genio DC BS-IV User Manual

Maintenance Manual MAN-00135
GENIO DC (BS-III & BS-IV) JULY 2011/Rev1
The repair methods given by the manufacturer in this document are based on the technical specifications, current at the time of release. The methods may be modified as a result of changes
introduced by the manufacturer in the production of the various component units and accessories from which the vehicles are manufactured. The reproduction, translation, transmission, in part of or
whole of the present document, are prohibited without the prior written consent of Mahindra & Mahindra Ltd. The use of this document by any person other than the trained personnel, at the
Authorized Service Centre of Mahindra & Mahindra Ltd., will amount to unauthorized use and shall be liable for penalty/prosecution © 2011 Mahindra & Mahindra Ltd.
46
• Lights, Horns, Wipers & Washers to be inspected at 5000kms,
10000kms, and then every 10000kms.
Lighting Control – Turn Indication
When the lever is pushed down to position C it causes the turn signals on the right side of the
vehicle to blink. When the lever is pulled upward to position A it causes the turn signals on the
left side of the vehicle to blink. As the turn is completed, the lever will automatically return to
the center position and turn OFF the signals at the same time.
Parking Lights – Turn the knob upward to first position switches ON the parking and side light
of the vehicle exterior lighting system.
Headlamp High beam – With the headlamp dipped beam ON, pushing stack downward
switches ON the headlamp high beam.
Headlamp ON dipped beam – Turn the knob upward to second position switches ON the
headlamp dipped beam.
Hazard warning indicator – Press the switch (located on the instrument panel) to activate all
turn-indications simultaneously.
NOTE: the direction indicators do not work when the hazard warning is activated.

Mahindra Genio DC BS-IV Specifications

General

Brand	Mahindra
Model	Genio DC BS-IV
Category	Automobile
Language	English

Summary

ABOUT THE MAINTENANCE MANUAL

Maintenance Schedule Overview

Outlines operations to be carried out at specified intervals. Includes Adjust, Inspect, Replace, Clean.

Standard Operating Procedures (SOP)

Explains each maintenance operation step-by-step with codes, man-hours, tools, and lubricants.

Check Sheets

Lists operations for technicians to perform during scheduled maintenance service.

GOOD WORKSHOP PRACTICES

Attire and Dress

Guidelines for technician's clothing and personal protective equipment.

Vehicle Protection

Procedures to protect vehicle components during maintenance operations.

Safety Precautions

Essential safety measures to follow during vehicle maintenance and repairs.

Parts and Tools Handling

Preparation and handling of tools, parts, and replacement items.

Removed Parts Handling

Proper procedures for managing parts that have been removed from the vehicle.

LSPV Spring Warning

Important caution regarding the LSPV spring when lifting the vehicle on a 2-post lift.

MAINTENANCE SCHEDULE

Engine Maintenance

Covers maintenance items related to the vehicle's engine.

Brake System Maintenance

Maintenance procedures for the vehicle's braking system.

Suspension System Maintenance

Maintenance for the vehicle's suspension components.

Steering System Maintenance

Maintenance procedures for the steering system.

Electrical System Maintenance

Maintenance for the vehicle's electrical components.

Tyre Maintenance

Maintenance related to vehicle tires.

MAINTENANCE PROCEDURES INDEX

Engine Oil Replacement

Procedure for replacing the engine oil.

Engine Oil Level Check

Procedure for checking the engine oil level.

Engine Oil Filter Replacement

Procedure for replacing the engine oil filter.

Coolant Replacement

Procedure for replacing the coolant.

Transmission Oil Replacement

Procedure for replacing transmission oil.

Differential Oil Replacement

Procedure for replacing rear differential oil.

Brake Pads/Calipers Check

Procedure for checking front and rear brake pads and calipers.

Wheel Alignment

Procedure for performing wheel alignment.

Tyre Pressure Check & Adjust

Procedure to check and adjust tyre pressure.

Headlamp Aiming/Alignment

Procedure for adjusting headlamp aiming.