To Next Page

To Previous Page

English – 23

6.9 - Deleting the Radio Transmitters

Table 17 - to delete all the radio transmitters

01. Press the key on the receiver and hold it down

02. Wait until the LED lights up, then wait until it goes off, then wait until it has flashed 3 times

03. Release the key precisely upon the third flash.

04. If the procedure is successful, after a few moments the LED will flash 5 times

TESTING AND COMMISSIONING

These are the most important phases in the automation’s arrangement to ensure maximum system safety.

3GDXLTRSADCNMDAX@PT@KHjDCDWODQSSDBGMHBH@MVGNVHKK@KRNQTMSGDSDRSRQDPTHQDCSNBGDBJSG@SSGDRNKTSHNMHR@OOQNOQH@SDENQ@MXQHRJR

and to check the observance of the law, standards and regulations: in particular, all requirements of EN 13241-1, EN 12445 and EN 12453.

Any supplementary equipment must be tested separately for operation and interaction with the SPIN: refer to the respective user manuals.

7.1 Testing

The testing procedure can also be performed as a periodic check of the automation devices. Each component of the system (sensitive edges,

OGNSNBDKKRDLDQFDMBXRSNODSBQDPTHQDR@RODBHjBSDRSHMFOG@RDENQSGDRDCDUHBDRNARDQUDSGDOQNBDCTQDRFHUDMHMSGDQDRODBSHUDHMRSQTBSHNM

manuals.

To test SPIN proceed as follows:

01. Ensure that the instructions outlined in chapter 1 “Warnings” have been observed in full.

02. Release the garage door by pulling

the release cord downwards and

see if you can manually move the

garage door in opening and closing

with a force of no more than 225N

03. Engage the carriage again.

04. Using the switch, the radio transmitter or the control cord test the opening and closing of the door and make sure that it moves in the

intended direction.

05. The test should be carried out a number of times to make sure that the door moves smoothly, that there are no points of excessive

friction and that there are no defects in the assembly or adjustments.

06. Check the proper operation of all the safety devices, one by one (photocells, sensitive edges, etc.). In particular, each time a device is

@BSHU@SDCSGDf!+4!42t+$#NMSGDBNMSQNKTMHSk@RGDRSHLDRPTHBJKXBNMjQLHMFSG@SSGDBNMSQNKTMHSQDBNFMHYDRSGDDUDMS

07. To check the photocells and make sure that there is no interference with other devices, pass a 5 cm diameter, 30 cm long cylinder on

SGDNOSHB@K@WHRjQRSMD@Q37SGDMMD@Q17@MCjM@KKX@SSGDLHCONHMSADSVDDMSGDL@MCL@JDRTQDSG@SHM@KKSGDRDB@RDRSGDCDUHBD

HRSQHFFDQDCRVHSBGHMFEQNLSGD@BSHUDSNSGD@K@QLRS@STR@MCUHBDUDQR@jM@KKXSG@SHSB@TRDRSGDHMSDMCDC@BSHNMHMSGDBNMSQNKTMHS

for example that it causes the reversal of the movement during the closing manoeuvre

08. If the dangerous situations caused by the movement of the door have been safeguarded by limiting the force of impact, the user must

measure the impact force according to EN Standard 12445.

If the adjustment of the “speed” and control of the “motor force” are used to assist the system for the reduction of the impact force, try

SNjMCSGD@CITRSLDMSSG@SFHUDRSGDADRSQDRTKSR

Nice SN6021 User Manual

Questions and Answers: