Nice SO2000 User Manual

18 – ENGLISH
LEVEL 2 FUNCTIONS (ADJUSTABLE PARAMETERS)
Entry LED Parameter LED (level) Set value Description
L4** FLASH output
L1 Door Open Indicator
Selects the device connected to the
FLASH output.
L2 Enabled if door closed
L3 Enabled if door open
L4 Warning light
L5 Electric latch
L6 Electric lock
L7 Suction cup
L8 Maintenance indicator
L5*
Motor force on
opening
L1 Force 1 (low)
Adjusts the motor force control system
to adapt it to the weight of the door
during the opening manoeuvre.
L2 Force 2
L3 Force 3
L4 Force 4
L5 Force 5
L6 Force 6
L7 Force 7
L8 Force 8 (high)
L6*
Motor force on
closing
L1 Force 1 (low)
Adjusts the motor force control system
to adapt it to the weight of the door
during the closing manoeuvre.
L2 Force 2
L3 Force 3
L4 Force 4
L5 Force 5
L6 Force 6
L7 Force 7
L8 Force 8 (high)
L7*
Maintenance
notice
L1
Automatic (depending on the severity of the
manoeuvres)
Adjusts the number of manoeuvres
after which the automation maintenance
request is triggered (see the “
“Maintenance notice” function”
paragraph).
L2 1000
L3 2000
L4 4000
L5 6000
L6 8000
L7 10000
L8 12000
L8
List of
malfunctions
L1 Result of 1st manoeuvre (most recent)
Allows for viewing the type of anomalies
that occurred in the last 8 manoeuvres
(refer to the “Anomaly log” paragraph).
This is a read-only parameter, which
means that its values cannot be
modied.
L2 Result of 2nd manoeuvre
L3 Result of 3rd manoeuvre
L4 Result of 4th manoeuvre
L5 Result of 5th manoeuvre
L6 Result of 6th manoeuvre
L7 Result of 7th manoeuvre
L8 Result of 8th manoeuvre
All parameters can be adjusted as desired without any problems; only the “Motor force on opening” and “Motor force on closing”
settings require special attention:
– high force values should not be used to compensate for points of abnormal friction on the leaf. Excessive force can jeopardise
the operation of the safety system or damage the leaf
– if the “Motor Force” control is used to aid the impact force reduction system, measure the force again after each adjustment in
accordance with the EN 12445 standard
– wear and atmospheric conditions inuence the door’s movement, so the force settings should be checked periodically.
(*) If the value of a parameter falls between two adjacent values, the control unit will switch on intermittently the two LEDs iden-
tifying the value itself. If necessary, the values can be rounded off by pressing the
p
or
q
button to round off respectively
to the higher or lower value among the two values highlighted by the control unit.
Example: Maintenance warning = 7000 manoeuvres - LEDs L5 and L6 ash. Pressing the
q
button rounds off to value L5
(6000), while pressing the
p
button rounds off to value L6 (8000).
If the value of a parameter is below the minimum value or above the maximum value among those listed in the table, the
control unit will switch on intermittently LED L1 or L8 respectively. If necessary, the values can be rounded off by pressing
the
p
or
q
button to round off to the nearest value.
Example: Pause Time = 5 seconds - LED L1 will ash. Pressing the
p
button rounds off to value L1 (10 s) and L1 will no
longer ash because the parameter will have been rounded off to a known value.
(**) If the conguration has not been learned, when LEVEL 2 of the MENU opens up, the control unit will propose the default
conguration.

Nice SO2000 Specifications

General

Brand	Nice
Model	SO2000
Category	Garage Door Opener
Language	English