Nice SO2000 User Manual

2 – ENGLISH
ENGLISH
Translation of the original instructions in full
CONTENTS
GENERAL SAFETY WARNINGS AND
PRECAUTIONS
1
1 GENERAL SAFETY WARNINGS AND PRECAUTIONS
1.1 GENERAL WARNINGS
a
Prior to installing the appliance, carefully read and
observe these instructions, since incorrect installa-
tion can cause serious harm to people and damage
to the appliance. Store them with care.
a
According to the latest European legislation, an
automated device must be constructed in conform-
ity to the harmonised rules specied in the current
Machinery Directive, which allow for declaring the
presumed conformity of the automation. Conse-
quently, all the operations for connecting the prod-
uct to the mains electricity, its commissioning and
maintenance must be carried out exclusively by a
qualied and expert technician.
a
In order to avoid any danger from inadvertent re-
setting of the thermal cut-off device, this appliance
must not be powered through an external switching
device, such as a timer, or connected to a supply
that is regularly powered or switched off by the cir-
cuit.
WARNING! Please abide by the following warnings:
– Before commencing the installation, check the “Prod-
uct technical specications”, in particular whether this
product is suitable for automating your guided part.
Should it not be suitable, do NOT proceed with the in-
stallation.
– The product cannot be used before it has been com-
missioned as specied in the “Testing and commis-
sioning” chapter.
– Before proceeding with the product’s installation,
check that all the materials are in good working order
and suited to the intended applications.
– The product is not intended for use by persons (includ-
ing children) with reduced physical, sensory or mental
capacities, nor by anyone lacking sufcient experience
or familiarity with the product.
– Children must not play with the appliance.
– Do not allow children to play with the product’s control
devices. Keep the remote controls out of reach of chil-
dren.
– The system’s power supply network must include a dis-
connection device (not supplied) with a contact open-
ing gap permitting complete disconnection under the
conditions envisaged by Overvoltage Category III.
– During the installation process, handle the product with
care by avoiding crushing, impacts, falls or contact
with liquids of any kind. Do not place the product near
sources of heat nor expose it to open ames. All these
actions can damage the product and cause it to mal-
function, or lead to dangerous situations. Should this
occur, immediately suspend the installation process
and contact the Technical Assistance Service.
1 GENERAL SAFETY WARNINGS AND PRECAUTIONS . . . . . 2
1.1 General warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.2 Installation warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2 PRODUCT DESCRIPTION AND INTENDED USE. . . . . . . . . . 3
2.1 List of constituent parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3 INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3.1 Pre-installation checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3.2 Product usage limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3.2.1 Product durability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3.3 Product identification and overall dimensions . . . . . . . . . . . 5
3.4 RECEIPT OF THE PRODUCT . . . . . . . . . . . . . . . . . . . . . . . . 5
3.5 Pre-installation works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.6 Installing the gearmotor . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.7 Manually unlocking and locking the gearmotor . . . . . . . . . . 8
4 ELECTRICAL CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . 8
4.1 Preliminary checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.2 Wiring diagram and description of connections . . . . . . . . . 9
4.2.1 Wiring diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.2.2 Description of connections . . . . . . . . . . . . . . . . . . . . . . . 9
4.3 Addressing of devices connected with the BlueBUS
system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.3.1 FT210B photosensor . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5 FINAL CHECKS AND START-UP. . . . . . . . . . . . . . . . . . . . . . 11
5.1 Power supply connection . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.2 Device learning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.3 Learning of the door opening and closing positions . . . . . 11
5.4 Checking the door movement . . . . . . . . . . . . . . . . . . . . . . 13
5.5 Connecting other devices . . . . . . . . . . . . . . . . . . . . . . . . . 13
6 TESTING AND COMMISSIONING . . . . . . . . . . . . . . . . . . . . . 13
6.1 Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6.2 Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
7 PROGRAMMING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
7.1 Using the programming buttons . . . . . . . . . . . . . . . . . . . . 15
7.2 Level 1 programming (ON-OFF) . . . . . . . . . . . . . . . . . . . . 16
7.2.1 Level 1 programming procedure . . . . . . . . . . . . . . . . . 16
7.3 Level 2 programming (adjustable parameters) . . . . . . . . . 17
7.3.1 Level 2 programming procedure . . . . . . . . . . . . . . . . . 17
7.4 Programming the direction . . . . . . . . . . . . . . . . . . . . . . . . 19
7.5 Resetting the encoder position . . . . . . . . . . . . . . . . . . . . . 19
7.6 Special functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
7.6.1 “Always open” function . . . . . . . . . . . . . . . . . . . . . . . . . 19
7.6.2 “Move anyway” function . . . . . . . . . . . . . . . . . . . . . . . . 19
7.6.3 “Maintenance notice” function . . . . . . . . . . . . . . . . . . . 19
7.7 Verifying the number of manoeuvres completed . . . . . . . . 20
7.8 Manoeuvre counter resetting . . . . . . . . . . . . . . . . . . . . . . . 20
7.9 Memory deletion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
8 TROUBLESHOOTING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . 21
8.1 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
8.2 Anomaly log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
8.3 Signalling through warning light . . . . . . . . . . . . . . . . . . . . 22
8.4 Signals on the control unit . . . . . . . . . . . . . . . . . . . . . . . . . 23
9 FURTHER DETAILS (Accessories). . . . . . . . . . . . . . . . . . . . 25
9.1 Modifying the STOP input configuration . . . . . . . . . . . . . . 25
9.2 Connecting an SM-type radio receiver . . . . . . . . . . . . . . . 25
9.3 Connecting and installing the back-up battery . . . . . . . . . 26
9.4 Connecting the Oview programmer . . . . . . . . . . . . . . . . . 27
9.5 Connecting the Solemyo solar energy system . . . . . . . . . 28
10 PRODUCT MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . 29
11 PRODUCT DISPOSAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
12 TECHNICAL SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . 30
13 CONFORMITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
INSTRUCTIONS AND WARNINGS FOR THE USER . . . . . . 33

Nice SO2000 Specifications

General

Brand	Nice
Model	SO2000
Category	Garage Door Opener
Language	English