Opus OP4 2020 User Manual

30 31
SETTING UP YOUR ANNEX
ANNEX COMPONENTS
1 x AIR OPUS Annex
1 x Cross lling tube
2 x AIR Annex side walls
2 x AIR Annex doors
1 x AIR Annex Ground Sheet
1. Locate the Annex air transfer valve inside your OPUS. This is the black valve located on your main air beam in the camper
on the door-side, just above the window.
2. Install the Cross Filling Tube by unscrewing the top of the black valve, pushing the gray tube on to the valve and then
threading the top of the black valve over the tube and twisng it on. Thread the end of the Cross Filling Tube through the
silver loop hole in the OPUS side wall.
3. Open the air transfer valve – please note that this will cause your tent to deate. You can also open the quick release
valves to deate faster. You will need to do this to aain easy access to the zip line aachment on the front face of your
tent
4. Open up the main secon of your annex. Idenfy the zip & Velcro line which is how your will aach the annex to your
main tent and layout lay out your annex with the two front door secons furthest from the camper.
5. Our recommendaon is to then stand between the OPUS and the annex and start zipping at the door side, walking
backwards between the OPUS and the annex as you close the zip. This will assist in locang both the Cross Filling Tube
that you installed on the main OPUS tent as well as the receiving valve on the annex-side about half-way along the zip
line. The receiving valve is located on the central air pole of your annex.
6. Once located, connect the Cross Filling Tube to the receiving valve on the side of the annex. Take care to ensure that the
spring is inside the grey tube to help protect the hose from geng kinked. Install the tube to the receiving valve in the
same way as in step (2) except you will need to thread the top of the valve on to the Cross Filling Tube before you push
the tube on to the valve. Twist the top of the valve on, to secure the tube in place.
7. Open the valve on the annex-side. Finish zipping the annex to the side of the OPUS and fold the Velcro ap over the zip.
8. Ensure all 7 quick-release valves are closed on the annex and all 5 on your OPUS main tent then press the AIR compressor
buon on the control panel and wait for the annex to inate.
9. Keep an eye out for obstrucons and when the annex is starng to form, feel free to help guide the air beams to assist
in easy owof air through them and form nal annex structure.
10. Once your annex has inated, you may nd that the posion of the AIR poles needs adjusng so that the annex is fully
tensioned. There are black straps between the oor-ends of the beams on the main tent secon, which will help to
ensure the opmal placement of the beams. You can then peg the corners and guide ropes of the AIR annex to the
ground to secure your posion.
11. Lay your oponal ground sheet and aach this to the main tent using the zippers provided. There are zip-open secons
of your ground sheet to allow the kitchen and fridge to slide out. You can also then zip on your side walls.
12. Aach Velcro seals between canopy and annex
AIR OPUS® TIP: You may nd that the AIR annex is easier to shape with the side walls and front doors zipped closed, as this helps to create more structure
to prevent the annex poles from distorng by over-extension when inang.
AIR OPUS® TIP: If your annex takes longer than usual to inate check that your quick-release valves are all fully closed and that none of the AIR poles are
pinched, prevenng AIR moving through. If this happens, you can easily move the air pole to allow AIR ow through and allow the pole to inate.

Opus OP4 2020 Specifications

General

Brand	Opus
Model	OP4 2020
Category	Utility Vehicle
Language	English