Sanyo PLC-XF47 User Manual

57
Maintenance and Care
Check the number of lamp to be replaced on the Lamp
Status Display.
Remove the two screws on the Lamp Cover and press
the button to open the Lamp Cover. (See the right figure.)
1
3
Loosen two screws and pull out the Lamp to be replaced
by grasping handle.
4
Turn off the projector and unplug the AC Power Cord. Let
the projector cool for at least 45 minutes.
2
Replace the Lamp with a new one and tighten two
screws. Make sure the Lamp is set properly.
6
Follow these steps to replace the lamp.
Put the Lamp Cover back and tighten two screws.
5
7
8
Connect the AC Power Cord to the projector and turn on
the projector.
Reset the Lamp Replacement Counter. (Refer to section
"Resetting the Lamp Counter" on page 58.)
NOTE : Do not reset LAMP REPLACEMENT COUNTER when
lamp is not replaced.
BUTTON
SCREWS
LAMP
COVER
SCREWS
Make sure which number of lamp needs to be
replaced on Lamp Status Display.
Figure shows case of replacing LAMP 2.
LAMP 1
LAMP 2
LAMP 3
LAMP 4
CAUTION : DO NOT OPERATE A PROJECTOR WHILE ANY OF LAMPS IS REMOVED. IT MAY RESULT IN
MALFUNCTIONS, FIRE HAZARD, OR OTHER ACCIDENTS.
NOTES ON LAMP REPLACEMENT
To maintain quality of picture (better balance of color and brightness in entire screen), we
recommend replacing all 4 lamps at a time.
Lamp Replacement
For continued safety, replace with a lamp assembly
of the same type.
Do not drop the lamp assembly or touch a glass
bulb! The glass can shatter and may cause injury.
Allow a projector to cool, for at least 45 minutes
before you open Lamp Cover. The inside of a
projector can become very hot.
CAUTION
TURN OFF THE UV LAMP BEFORE
OPENING THE LAMP COVER.
WARNING:
When the projection lamp of the projector reaches its end of life, the Lamp replacement icon appears on the
screen and LAMP REPLACE indicator lights orange. Replace the lamp with a new one promptly. The timing
when the LAMP REPLACE indicator should light is depending on the lamp mode.
Indicators
LAMP REPLACE indicator
Lamp replacement icon
READY
✔Note:
• The Lamp replacement icon will not appear when
the Display function is set to “Off” (p.47), during
“Freeze” (p.28), or “No show” (p.29).
Downloaded From projector-manual.com Sanyo Manuals

Sanyo PLC-XF47 Specifications

General

Vertical scan range	48 - 120 Hz
Horizontal scan range	15 - 120 kHz
Projection technology	LCD
Contrast ratio (typical)	2000:1
Screen size compatibility	40 - 600 \
Projector native resolution	XGA (1024x768)
Keystone correction, vertical	80 °
Keystone correction, horizontal	40 °
I/O ports	Analog (D-sub15), Serial in & Serial out (D-Sub 9 x 2)
Video out	UXGA, SXGA+, SXGA, WXGA, XGA, SVGA, VGA, MAC
Resolution	2359296 pixels
Aspect ratio	4:3
RS-232 ports	1
Dimensions (WxDxH)	581 x 815.5 x 251.5 mm
Power requirements	200-240 V AC 9.7 A Max, 50 / 60 Hz
Connectivity technology	Wired
Lamp type	NSH
Lamp power	330 W
Light source type	Lamp
Dot clock scanning frequency	230 MHz
Serial interface type	RS-232
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Power consumption (typical)	1700 W

Weight and Dimensions

Weight	36500 g