Cabinet Details31

Supply Scope31

Input / Output Section31

Cell Section32

Control Section32

Control Door Cabinet Components34

Figure 3-1 Multi-Language Keypad and Display Interface35

Figure 3-2 Operator Panel KTP70036

Fault Reset37

Cooling Section39

Maintenance41

Description of the Option Codes42

Modbus Interface (Software Activation) (Option G22)42

Modbus Interface (Software Activation) (Option G32)42

Devicenet Profile 12 Interface (Option G23)42

Devicenet Profile 12 Interface (Option G43)42

Control Net Interface (Option G26)42

Control Net Interface (Option G46)42

Modbus Ethernet Interface (Software Activation) (Option G28)42

Modbus Ethernet Interface (Software Activation) (Option G38)43

PROFIBUS DP (Option G91)43

PROFIBUS DP (Option G93)43

Connection for Control Voltage Provided by Customer AC 220/230 V (Option K68)43

Control Voltage AC 12 V Internal (Option K69)43

Connection for Control Voltage Provided by Customer AC 120 V (Option K79)43

Output Reactor (Option L09)43

Bidirectional Synchronized Bypass Operation (Option L29)44

Cabinet Illumination and Service Socket in Trigger and Control Section (Option L50)45

Cabinet Anti-Condensation Heating, Temperature-Monitored (Option L55)46

X 2 Thermistor Protection Relays for Alarms and Faults (Option L81)46

X 2 Thermistor Protection Relays for Alarms and Faults (Option L82)46

Figure 3-3 Cabinet Anti-Condensation Heating46

Pt100 Evaluation Units with 3 Inputs each (Option L91)47

Pt100 Evaluation Unit with 6 Inputs and 2 Analog Outputs (Option L93)47

Pt100 Evaluation Unit with 6 Inputs for Ex-Proof Motors And6 Analog Outputs(Option L95)47

Mechanical Safety Locking System - Castell (Option M10)48

Gland Plates (Option M35)48

Figure 3-4 Principle of the Mechanical Safety Locking System - Castell48

Gland Plates (Option M36)49

Gland Plates (Option M37)49

IP42 Degree of Protection (Option M42)49

Redundant Fan (Option M61)49

Drive Prepared for Duct Flange Connection in Front (M64)49

Harsh Environment Conditions (M67)50

Drive Prepared for Duct Flange Connection in Rear (M68)50

Extended Space for Bottom Cable Entry (Option M69)51

Controlled Outgoing Circuit for Auxiliary Equipment 400 V 3 AC or 460/480 V 3 AC (Option N30)51

Controlled Outgoing Circuit for Auxiliary Equipment 400 V 3 AC or 460/480 V 3 AC (Option N31)52

Table 3-1 Outgoing Circuit for Auxiliary Equipment (Option N30)52

Table 3-2 T-X30 Terminal Strip for Connecting Auxiliary Equipment52

Table 3-3 Outgoing Circuit for Auxiliary Equipment (Option N31)52

Controlled Outgoing Circuit for Auxiliary Equipment 400 V 3 AC or 460/480 V 3 AC (Option N32)53

Table 3-4 T-X30 Terminal Strip for Connecting Auxiliary Equipment53

Table 3-5 Outgoing Circuit for Auxiliary Equipment (Option N32)53

Table 3-6 T-X30 Terminal Strip for Connecting Auxiliary Equipment53

Controlled Outgoing Circuit for Auxiliary Equipment 400 V 3 AC or 460/480 V 3 AC (Option N33)54

Controlled Outgoing Circuit for Auxiliary Equipment 230 V 1 AC or 120 V 1 AC (Option N35)54

Table 3-7 Outgoing Circuit for Auxiliary Equipment (Option N33)54

Table 3-8 T-X30 Terminal Strip for Connecting Auxiliary Equipment54

Table 3-9 Outgoing Circuit for Auxiliary Equipment (Option N35)54

Controlled Outgoing Circuit for Auxiliary Equipment 230 V 1 AC or 120 V 1 AC (Option N36)55

Table 3-10 T-X30 Terminal Strip for Connecting Auxiliary Equipment55

Table 3-11 Outgoing Circuit for Auxiliary Equipment (Option N33)55

Table 3-12 T-X30 Terminal Strip for Connecting Auxiliary Equipment55

Controlled Outgoing Circuit for Auxiliary Equipment 230 V 1 AC or 120 V 1 AC (Option N37)56

Controlled Outgoing Circuit for Auxiliary Equipment 230 V 1 AC or 120 V 1 AC (Option N38)56

Table 3-13 Outgoing Circuit for Auxiliary Equipment (Option N33)56

Table 3-14 T-X30 Terminal Strip for Connecting Auxiliary Equipment56

Table 3-15 Outgoing Circuit for Auxiliary Equipment (Option N33)56

Motor-Side Grounding Switch (Option N45)57

Power Supply for Auxiliaries 24 V DC/2.5 a (Option N75)57

Cell Bypass (Option U11)57

Individual Redundant Cell (Option U12)57

Table 3-16 T-X30 Terminal Strip for Connecting Auxiliary Equipment57

Redundant Cell Rank (Option U13)58

Sinusodial Filter (Option Y15)58

Brand	Siemens
Model	GH180
Category	Power Tool
Language	English

Siemens GH180 User Manual

Table of Contents

Questions and Answers:

Siemens GH180 Specifications

Related product manuals