Siemens SINUMERIK 808D ADVANCED User Manual

Table of contents
Parameter Manual
4 Operating Instructions, 08/2013, 6FC5397-8EP40-0BA0
5.2.2 Signals to MCP ........................................................................................................................ 424
5.2.3 Reading/writing NC data: Job .................................................................................................. 425
5.2.4 Reading/writing NC data: Result .............................................................................................. 425
5.2.5 PI service: Job ......................................................................................................................... 426
5.2.6 PI service: Result ..................................................................................................................... 426
5.3 Retentive data area ................................................................................................................. 426
5.4 User Alarms............................................................................................................................. 427
5.4.1 User alarms: Activating ............................................................................................................ 427
5.4.2 Variables for user alarms ......................................................................................................... 428
5.4.3 Active alarm response ............................................................................................................. 428
5.4.4 Alarm acknowledgement ......................................................................................................... 428
5.5 Signals from/to HMI ................................................................................................................. 429
5.5.1 Program control signals from the HMI (retentive area) ............................................................ 429
5.5.2 Program selection from PLC (retentive area) .......................................................................... 429
5.5.3 Checkback signal: Program selection from HMI (retentive area) ............................................ 430
5.5.4 Signals from HMI ..................................................................................................................... 430
5.5.5 Signals from PLC ..................................................................................................................... 430
5.5.6 Signals to maintenance planners ............................................................................................. 431
5.5.7 Signals from maintenance planners ........................................................................................432
5.5.8 Signals from operator panel (retentive area) ........................................................................... 432
5.5.9 General selection/status signals from HMI (retentive area) ..................................................... 432
5.5.10 General selection/status signals to HMI (retentive area) ......................................................... 433
5.6 Auxiliary functions transfer from NC channel........................................................................... 433
5.6.1 Overview .................................................................................................................................. 433
5.6.2 Decoded M signals (M0 to M99) .............................................................................................. 434
5.6.3 Transferred T functions ............................................................................................................ 435
5.6.4 Transferred M functions ........................................................................................................... 435
5.6.5 Transferred S functions ........................................................................................................... 435
5.6.6 Transferred D functions ........................................................................................................... 436
5.6.7 Transferred H functions ........................................................................................................... 436
5.7 NCK signals............................................................................................................................. 436
5.7.1 General signals to NCK ........................................................................................................... 436
5.7.2 General signals from NCK ....................................................................................................... 437
5.7.3 Signals at fast inputs and outputs ............................................................................................ 438
5.7.4 Signals from fast inputs and outputs .......................
.......
.......................................................... 439
5.8 Channel signals ....................................................................................................................... 440
5.8.1 Signals to NC channel ............................................................................................................. 440
5.8.2 Signals from NC channel ......................................................................................................... 443
5.9 Axis/spindle signals ................................................................................................................. 447
5.9.1 Transferred M and S functions, axis specific ........................................................................... 447
5.9.2 Signals to axis/spindle ............................................................................................................. 447
5.9.3 Signals from axis/spindle ......................................................................................................... 450
5.10 PLC machine data ................................................................................................................... 452
5.10.1 INT values (MD 14510 USER_DATA_INT) .............................................................................. 452
5.10.2 HEX values (MD 14512 USER_DATA_HEX) .......................................................................... 453
5.10.3 FLOAT values (MD 14514 USER_DATA_FLOAT) .................................................................. 453
5.10.4 User alarm: Configuring (MD 14516 USER_DATA_PLC_ALARM) ......................................... 453
5.11 Signals, synchronized actions ................................................................................................. 454

Siemens SINUMERIK 808D ADVANCED Specifications

General

Brand	Siemens
Model	SINUMERIK 808D ADVANCED
Category	Control Unit
Language	English