TC-Helicon VoiceLive Touch2 User Manual (English)

To Next Page

To Previous Page

adVanced loop function tutorial

• Tap the Loop button once or twice to display the loop functions

menu (Erase, Clear etc).

• Tap the Matrix button associated to MET: so it shows “MET:ON.”

You will hear the metronome.

• Use the Tap button to adjust the tempo if needed.

• Record a loop, tapping the Record and Play buttons as close as

possible to the Metronome tempo. Your button taps are corrected

to help you make better, more rhythmic loops.

• Set MET to SHH (quantized Rec/Loop but metronome sound

muted) or OFF (no Assist, muted metronome sound) if you prefer.

Otherwise leave it on.

• Tap the Loop mode button to switch to the loop selection menu

(showing the “Select”, “Mute” and “Shots” labels). As you see, this

menu gives you access to six loop slots (“Loop1” to “Loop6”).

• Ensure SELECT is highlighted before tapping an open loop slot.

• Record additional loop layers in each of the slots. Slots can be se-

lected and new loops recorded while Record is enabled. This helps

you build loops quickly.

• Select MUTE and tap the Matrix buttons corresponding to the six

loop layers to mute and unmute them.

• Select SHOTS to solo and play one layer at a time.

loopinG

Basic looping in Home mode

• Find a preset you like.

• To start recording, tap the Record button on the downbeat of a

rhythmic singing performance.

Store

INPUT

Home

Hold for Genre

Effects

Voices

Tap

Mix

Setup

Loop

Hit

Hold for Talk

Edit

• To stop recording, tap Record again. You will immediately hear the

loop you just recorded.

• If you want to set the loop point and continue recording immedi-

ately, tap the Play button instead. This will allow you to overdub

your first recording without any delay.

• To stop and start loop playback, tap the Play button.

Store

INPUT

Home

Hold for Genre

Effects

Voices

Tap

Mix

Setup

Loop

Hit

Hold for Talk

Edit

• To erase your loop, hold the Record button while playback/record-

ing is stopped.

Advanced looping in Loop mode

You can access additional looping functions by tapping the Loop button:

• LoopAssist (Metronome and quantization functions)

• Loop layering (up to 6 independent layers)

• Loop effects controlled by the Slider FX Bar

• Erase, Undo etc.

Looping

Need help?

Do you have a question about the TC-Helicon VoiceLive Touch2 and is the answer not in the manual?

TC-Helicon VoiceLive Touch2 Specifications

Analog Inputs

mic input impedance	3.08/1.54 kOhm
mic input level at 0 dBFS	-42 dBu to +4.2 dBu
mic equivalent input noise at max mic gain Rg = 150 Ohm	-127 dBu
mic signal-to-noise ratio	>100 dB
guitar input impedance	1 MOhm
guitar input level at 0 dBFS	-7 dBU to 17 dBu
guitar input signal-to-noise ratio	>108 dB
aux input level at 0 dBFS	+2 dBu
analog to digital conversion	24 Bit, 128 x oversampling bitstream, 110 dB SNR A-weighted

Analog Outputs

output impedance balanced/unbalanced	80/40 Ohm
output range line	+2 dBu
dynamic range	>109 dB, 20 Hz to 20 kHz
frequency response	+0/-0.3 dB, 20 Hz to 20 kHz
headphone out	+17 dBu max (50 mW max)
digital to analog conversion	24 Bit, 128 x oversampling bitstream, 115 dB SNR A-weighted

Power