EasyManuals Logo
Home>TurboChef>Oven>TORNADO

TurboChef TORNADO Service Manual

TurboChef TORNADO
94 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #29 background imageLoading...
Page #29 background image
USER CONFIGURABLE OPTIONS - ENABLE/DISABLE CODES
The following codes enable and disable each function/screen listed. They do not take you to the function/screen.
After each code, press
ENTER. To enable, press 9 after entering code (except S-A-V-E, W-A-V-E). To disable, press
any key (except 9) after entering code.
Function/Screen Simultaneously Press Enter Key Code
Done Screen w/out “Save Time”
BACK & ENTER 3-6-6-3 (D-O-N-E)
Done Screen w/ “Save Time” - step 1 BACK & ENTER 3-6-6-3 (D-O-N-E)
Done Screen w/ “Save Time” - step 2
BACK & ENTER 8-4-6-3 (T-I-M-E)
Edit Recipe Mode
UP
& DOWN 8-4-3-3 (T-I-D-E)
Load Menu from Card BACK & ENTER 6-3-6-8 (M-E-N-U)
Save Menu to Card - step 1 BACK & ENTER 6-3-6-8 (M-E-N-U)
Save Menu to Card - step 2
BACK
& ENTER 7-2-8-3 (S-A-V-E)
Snooze Screen
BACK & ENTER 7-6-6-9 (S-N-O-Z)
Time Screen (Figure 16)
BACK & ENTER 8-4-6-3 (T-I-M-E)
Timed Mag Test
BACK
& ENTER 9-2-8-3 (W-A-V-E)
- Some codes are not available on some ovens.
- Oven must be in Off or Cooling Down mode.
USER CONFIGURABLE OPTIONS - ACCESS CODES
The following codes allow access to each function/screen listed. To enable/disable these codes (where applicable),
see above. After each code, press ENTER.
Function/Screen
Simultaneously Press Enter Key Code
Edit Recipe Mode UP & DOWN 9 (or as specified - see “Set PIN” below)
Erase Menu* BACK & ENTER 3-7-2-7 (E-R-A-S)
Load Menu from Card
Bottom-left, then upper-mid soft key
Master Reset BACK & ENTER 9-4-7-1
Save Menu to Card
Bottom-left, then lower-mid soft key
Set PIN**
UP
& DOWN 3-3-4-8 (E-D-I-T)
Test Mode BACK & ENTER 9-4-2-8 (W-H-A-T)
Unit Test
BACK & ENTER 8-6-4-8 (U-N-I-T)
View Cook Counts 1 & 3
View Faults***
4 & 6
Zero Cook Counts* BACK & ENTER 6-7-3-9 (O-R-E-Z)
- Oven must be in Off or Cooling Down mode.
* To execute, press 3 after entering code.
**
Set PIN after entering code. Accessing “Edit Recipe Mode” will now require new PIN instead of 9.
*** To view voltage, press ENTER. To initiate a self test, press the corresponding soft key from the voltage screen.
19
THE CONTROL SYSTEM

Table of Contents

Other manuals for TurboChef TORNADO

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the TurboChef TORNADO and is the answer not in the manual?

TurboChef TORNADO Specifications

General IconGeneral
BrandTurboChef
ModelTORNADO
CategoryOven
LanguageEnglish

Related product manuals