To Next Page

To Previous Page

22 D-303973 PowerMaxExpress Installer's Guide

GPRS Up / Down [Fig 4.5.3(23)]

My SIM Tel. # [Fig 4.5.3(23a)]

Here you enter the PowerMax SIM card telephone number.

The central station dials this number when it needs to

connect to the PowerMaxExpress for uploading /

downloading data.

Caller ID# [Fig 4.5.3(23b)]

Here you determine the 1

IPMP receiver telephone

number. When the PowerMaxExpress responds to an

incoming call from the telephone number defined here, it

creates a connection to the IPMP for uploading /

downloading data.

Note: Caller ID#1 / ID#2 should be 6 or more digits for

wake-up by IPMP to work.

Caller ID# [Fig 4.5.3(23c)]

Here you determine the 2

IPMP receiver telephone

number. When the PowerMaxExpress responds to an

incoming call from the telephone number defined here, it

creates a connection to that IPMP for uploading /

downloading data.

Report Cnfrm Alarm [Fig 4.5.3(24)] - see note in Fig. 4.5

Detail C

Here you determine whether the system will report

whenever 2 or more events (confirmed alarm) occur

during a specific period (see par. 4.4.33).

Available options are: enable report, disable report,

enable + bypass (enabling report and bypassing the

detector - applicable to PowerMaxExpress that is

compatible with DD243 standard).

Report 24H Zones (Optional) [Fig 4.5.3(25)]

Here you determine whether 24 hour (silent and audible) zones

will function as normal 24 hour zones or as panic zones.

The options are: both original, audible as panic, silent

as panic, or both as panic.

Recent Close [Fig 4.5.3(26)]

Here you enable or disable the “recent closing” report, that is

sent to the central station if an alarm occurs within 2 minutes

from the expiry of the exit delay.

The options are: recent close ON and recent close OFF.

Zone restore [Fig 4.5.3(27)]

Here you determine whether a zone restore will be

reported or not.

The options are: report restore and don't report.

System Inactivity Report [Fig 4.5.3(28)]

Here you determine whether the central station will receive

a message if the system is inactive (not armed) during a

defined period (days).

The options are: disable, rep. after 7d, rep. after 14d,

rep. after 30d, rep. after 90d.

Call Waiting OFF (Optional) [Fig 4.5.3(29)]

Here you enter a code to cancel "call waiting" when calling

the central station.

4.5.4 Private Report (Fig. 4.5)

Voice Report [Fig 4.5.4(1)]

Reported Events [Fig 4.5.4(1a)]

Here you configure reporting to private phone (voice). The

event groups may vary depending on the inclusion of voice

control with your PowerMaxExpress panel.

Term

Description

alarms+alerts

Alarm and alert messages

alarms

Alarm messages

alerts

Alert messages

disable report

No message will be reported (default).

Private Tel# [Fig 4.5.4(2b)]

Here you program the 1

telephone number (including area

code, if required) of the private subscriber to which the

system will report the event groups defined in Report To

Private.

Private Tel# [Fig 4.5.4(2c)]

Here you program the 2

telephone number (including area

code, if required) of the private subscriber to which the

system will report the event groups defined in Report To

Private.

Private Tel# [Fig 4.5.4(2d)]

Here you program the 3

telephone number (including area

code, if required) of the private subscriber to which the

system will report the event groups defined in Report To

Private.

Private Tel# [Fig 4.5.4(2e)]

Here you program the 4

telephone number (including area

code, if required) of the private subscriber to which the

system will report the event groups defined in Report To

Private.

Redial Attempts [Fig 4.5.4(2f)]

Here you determine the number of times the communicator

will dial the called party’s number (private telephone).

The options are: 1, 2, 3 and 4 attempts.

Attention! A maximum of 2 dialing attempts is permitted

by the Australian Telecommunication Authority.

Tel. acknowledge [Fig 4.5.4(2f)]

Here you determine whether the system will use the single

acknowledge or the all acknowledge mode when reporting to

private telephones.

Note: In the single acknowledge mode, receiving an

acknowledge signal from a single telephone is sufficient to

consider the current event closed and call off the

communication session. The remaining telephones serve for

backup purposes only. In the all acknowledge mode, an

acknowledge signal must be received from each telephone

before the current event is considered reported.

The options are: single ack and all ack.

SMS Report Tel# [Fig 4.5.4(2)]

Reported Events [Fig 4.5.4(2a)]

Here you configure reporting by SMS. The event groups

are identical to those described in the Voice

Report>Reported Events section above.

SMS Tel# [Fig 4.5.4(2b)]

Here you define the first SMS phone number (including

area code, 16 digits maximum) to which pre-selected

event types (see par. 4.6.3) will be reported.

SMS Tel# [Fig 4.5.4(2c)]

Here you define the second SMS phone number (including

area code, 16 digits maximum) to which pre-selected

event types (see par. 4.6.3) will be reported.

SMS Tel# [Fig 4.5.4(2d)]

Here you define the third SMS phone number (including

area code, 16 digits maximum) to which pre-selected

event types (see par. 4.6.3) will be reported.

SMS Tel# [Fig 4.5.4(2e)]

Here you define the fourth SMS phone number (including

area code, 16 digits maximum) to which pre-selected

event types (see par. 4.6.3) will be reported.

Brand	Visonic
Model	POWERMAXEXPRESS
Category	Security System
Language	English

Visonic POWERMAXEXPRESS Installer's Guide

Table of Contents

Other manuals for Visonic POWERMAXEXPRESS

Questions and Answers:

Visonic POWERMAXEXPRESS Specifications

Related product manuals