EasyManuals Logo
Home>Xerox>Printer>Phaser 3250

Xerox Phaser 3250 User Guide

Xerox Phaser 3250
90 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #40 background imageLoading...
Page #40 background image
9.8 <
Troubleshooting>
Vertical lines If black vertical streaks appear on the page:
The drum inside the print cartridge has
probably been scratched. Install a new print
cartridge. See page 8.3.
If white vertical streaks appear on the page:
The surface of the LSU part inside the printer
may be dirty. Clean the LSU. See page 8.2.
Gray
background
If the amount of background shading becomes
unacceptable, the procedures below may fix the
problem.
Change to lighter weight paper. See page 5.3.
Check the printer’s environment; low humidity
(lower than 20% RH) or high humidity (higher
than 80% RH) conditions can increase the
amount of background shading.
Remove the old print cartridge and install a
new one. See page 8.3.
Toner smear Clean the inside of the printer. See page 8.1.
Check the paper type and quality. See page
5.2.
Remove the print cartridge and install a new
one. See page 8.3.
Vertical
repetitive
defects
If marks repeatedly appear on the printed side of
the page at even intervals:
The print cartridge may be damaged. If a
repetitive mark occurs on the page, install a
new print cartridge. See page 8.3.
Parts of the printer may have toner on them. If
the defects occur on the back of the page, the
problem will likely correct itself after a few
more pages.
The fusing assembly may be damaged.
Contact a service representative.
Condition Suggested solutions
Background
scatter
Background scatter results from bits of toner
distributed on the printed page.
The paper may be too damp. Try printing with
a different batch of paper. Do not open
packages of paper until necessary so that the
paper does not absorb too much moisture.
If background scatter occurs on an envelope,
change the printing layout to avoid printing
over areas that have overlapping seams on
the reverse side. Printing on seams can cause
problems.
If background scatter covers the entire
surface area of a printed page, adjust the print
resolution through your software application or
via the printer properties window.
Misformed
characters
If characters are improperly formed and
producing hollowed images, the paper stock
may be too slick. Try a different paper. See
page 5.3.
Page skew Ensure that the paper is loaded properly.
Check the paper type and quality. See page
5.2.
Ensure that the paper is loaded correctly and
the adjustable guides are not too tight or too
loose against the paper stack.
Curl or wave Ensure that the paper is loaded properly.
Check the paper type and quality. Both high
temperature and humidity can cause paper
curl. See page 5.2.
Turn over the stack of paper in the tray. Also
try rotating the paper 180° in the tray.
Condition Suggested solutions

Table of Contents

Other manuals for Xerox Phaser 3250

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Xerox Phaser 3250 and is the answer not in the manual?

Xerox Phaser 3250 Specifications

General IconGeneral
ColorNo
Print technologyLaser
Maximum resolution600 x 600 DPI
Warm-up time (from sleep mode)15 s
Time to first page (black, normal)8.5 s
Print speed (black, normal quality, A4/US Letter)28 ppm
Internal memory32 MB
Maximum internal memory160 MB
Sound power level (standby)29 dB
Sound pressure level (printing)54 dB
Total input capacity251 sheets
Maximum input capacity501 sheets
Paper tray media typesBond paper, Envelopes, Labels, Plain paper, Recycled paper, Transparencies
FunctionsPrint
I/O portsUSB 2.0
Device managerPrinter Setting Utility for Windows
Package length561.33 mm
Depth (imperial)14.5 \
Width (imperial)14.3 \
Height (imperial)9.4 \
Weight (imperial)26.19 lbs
Power requirements240 V, 50/60 Hz
Storage drive typeN/A
Hardware scan resolution1200 x 1200 DPI
Storage temperature (T-T)32 - 104 °F
Power consumption (active)400 W
Compatible operating systemsFedora Core 1, Red Hat 9, SUSE 9 Windows 2000/Vista
Non-operating relative humidity (non-condensing)20 - 80 %
Country of originChina
Maximum duty cycle30000 pages per month
Recommended duty cycle4000 pages per month
Sustainability certificatesENERGY STAR
Power consumption (standby)70 W
Power consumption (PowerSave)11 W
Operating temperature (T-T)10 - 32 °C
Operating relative humidity (H-H)10 - 80 %
CertificationCE, UL 60950-1/CSA 60950-1-03, EMC 2004/108/EC, 2006/95/EC
Package width472.43 mm
Package height342.89 mm
Package weight11884.3 g
Weight and Dimensions IconWeight and Dimensions
Depth369 mm
Width364 mm
Height239.2 mm
Dimensions (WxDxH)364 x 369 x 239.2 mm

Related product manuals