EasyManuals Logo
Home>Yealink>IP Phone>SIP-T40G

Yealink SIP-T40G Administrator's Guide

Yealink SIP-T40G
572 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #362 background imageLoading...
Page #362 background image
Administrator’s Guide for SIP-T2 Series/T4 Series/T5 Series/CP920 IP Phones
359
Example:
“235x! would match “2351”, “2352”, “2353”, and so on. The number starting with 235 will be blocked to
dial out.
,
The comma “,” can be used as a separator to generate a secondary dial tone.
Example:
“<9,:55>xx”, after entering digit “9”, secondary dial tone plays and you can complete the remaining two-
digit number.
Note: The secondary dial tone can be customized. For more information, refer to Tones.
A
The letter “A” indicates the account that is applied to the digit map. You can use A alone or a com-
bination of A and account ID (for example, <A1>).
Example:
“123A”, the default account will be applied to the digit map.
“123<A2>”, the second account will be applied to the digit map.
Note: It is not applicable to the digit map on a per-line basis.
Digit Map for All Lines Configuration
The following table lists the parameters you can use to configure the digit map for all lines.
Parameter
dialplan.digitmap.enable <y0000000000xx>.cfg
Description
It enables or disables the digit map feature.
Note: The value configured by the parameter “account.X.dialplan.digitmap.enable” takes precedence
over that configured by this parameter.
Permitted
Values
0-Disabled
1-Enabled
Default
0
Parameter
dialplan.digitmap.string <y0000000000xx>.cfg
Description
It configures the digit map pattern used for the dial plan.
Example:
dialplan.digitmap.string = <[2-9]x:86>3.T|0x.!|1xxx
Note: The string must be compatible with the digit map feature of MGCP described in 2.1.5 of RFC
3435. It works only if “dialplan.digitmap.enable” or “account.X.dialplan.digitmap.enable” is set to 1
(Enabled). The value configured by the parameter “account.X.dialplan.digitmap.string takes pre-
cedence over that configured by this parameter.
Permitted
Values
String within 2048 characters
Default
[2-9]11 | 0T | 011xxx.T | [0-1][2-9]xx xxxxxxx | [2-9]xx xxxxxxx | [2-9]xxxT | **x.T | +x.T| 00x.T
Parameter
dialplan.digitmap.interdigit_long_timer <y0000000000xx>.cfg
Description
It configures the time (in seconds) for the phone to wait before dialing an entered number if it matches
part of any string of the digit map.
If it is set to 0, the phone will not dial the entered number if only a partial match exists.
The value of this parameter should be greater than that configured by the parameter “dial-
plan.digitmap.interdigit_short_timer”.
For example:

Table of Contents

Other manuals for Yealink SIP-T40G

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Yealink SIP-T40G and is the answer not in the manual?

Yealink SIP-T40G Specifications

General IconGeneral
MountingDesk/Wall
Handset typeWired handset
Product typeIP Phone
Product colorBlack
Wall mountableYes
Wi-FiNo
Security algorithmsAES, HTTPS, SSL/TLS
Networking standardsIEEE 802.3af
Ethernet LAN interface typeGigabit Ethernet
Supported network protocolsFTP, TFTP, HTTP, HTTPS
Voice codecsG.711, G.711a, G.711u, G.722, G.726, G.729ab
RJ-11 ports quantity1
Ethernet LAN (RJ-45) ports2
AC adapter input voltage100 - 240 V
AC adapter output current0.6 A
AC adapter output voltage5 V
Power consumption (typical)1.6 W
CertificationCE, FCC, ISO 9001
Operating temperature (T-T)-10 - 50 °C
Operating relative humidity (H-H)10 - 90 %
Volume controlDigital
Display diagonal2.3 \
Display resolution132 x 64 pixels
Lines quantity3 lines
Phonebook capacity1000 entries
Number of VoIP accounts3
Number of handles included1 pc(s)
Weight and Dimensions IconWeight and Dimensions
Depth175 mm
Width212 mm
Height54 mm

Related product manuals