Yealink SIP-T40G Administrator's Guide

Administrator’s Guide for SIP-T2 Series/T4 Series/T5 Series/CP920 IP Phones
395
[1]
X is the account ID. For T57W/T54W/T48U/T48S/T48G/T46U/T46S/T46G/T29G, X=1-16; for
T53W/T53/T43U/T42U/T42G/T42S, X=1-12; for T41P/T41S/T27G, X=1-6; for T40P/T40G/T23P/T23G, X=1-3; for T21
(P) E2, X=1-2.
Music on Hold (MoH) Configuration
When a call is placed on hold, the phone will send an INVITE message to the specified MoH server account accord-
ing to the SIP URI. The MoH server account automatically responds to the INVITE message and immediately plays
audio from some source located anywhere (LAN, Internet) to the held party. For more information, refer to draft RFC
draft-worley-service-example.
The following table lists the parameters you can use to configure music on hold.
Parameter
account.X.music_server_uri
[1]
<MAC>.cfg
Description
It configures the address of the Music On Hold server.
Examples for valid values: <10.1.3.165 > , 10.1.3.165, sip:moh@sip.com, <sip:moh@sip.com > ,
<yealink.com > or yealink.com.
Note: The DNS query in this parameter only supports A query.
Permitted
Values
SIP URI within 256 characters
Default
Blank
Web UI
Account > Advanced > Music Server URI
Parameter
account.X.music_on_hold_type
[1]
<MAC>.cfg
Description
It configures the way to process Music On Hold when placing an active call on hold.
Permitted
Values
0-Calling the Music On Hold server before holding the call
1-Calling the Music On Hold server after holding the call
Default
0
[1]
X is the account ID. For T57W/T54W/T48U/T48S/T48G/T46U/T46S/T46G/T29G, X=1-16; for
T53W/T53/T43U/T42G/T42U/T42S, X=1-12; for T41P/T41S/T27G, X=1-6; for T40P/T40G/T23P/T23G, X=1-3; for T21
(P) E2, X=1-2; for T19(P) E2/CP920, X=1.
Call Mute
You can mute the microphone of the active audio device (handset, headset or speakerphone) on Yealink phones
during an active call or when the phone is on the pre-dialing/dialing/calling/ringing screen. The call is automatically
muted when setting up successfully. Muting before a call is answered prevents the other party from hearing the
local discussion.
You can activate the mute feature by pressing the MUTE key. Normally, the mute feature is automatically deac-
tivated when the active call ends. You can use keep mute feature to keep the mute state persisting across the calls.
Note: Muting microphone on the pre-dialing/dialing/calling/ringing screen is not available on T23P/T23G/T21(P) E2
phones when the keep mute feature is disabled.
Topics
Microphone Mute Configuration
Keep Mute
Mute Alert Tone
Microphone Mute Configuration
The following table lists the parameter you can use to configure the microphone mute feature.

Yealink SIP-T40G Specifications

General

Mounting	Desk/Wall
Handset type	Wired handset
Product type	IP Phone
Product color	Black
Wall mountable	Yes
Wi-Fi	No
Security algorithms	AES, HTTPS, SSL/TLS
Networking standards	IEEE 802.3af
Ethernet LAN interface type	Gigabit Ethernet
Supported network protocols	FTP, TFTP, HTTP, HTTPS
Voice codecs	G.711, G.711a, G.711u, G.722, G.726, G.729ab
RJ-11 ports quantity	1
Ethernet LAN (RJ-45) ports	2
AC adapter input voltage	100 - 240 V
AC adapter output current	0.6 A
AC adapter output voltage	5 V
Power consumption (typical)	1.6 W
Certification	CE, FCC, ISO 9001
Operating temperature (T-T)	-10 - 50 °C
Operating relative humidity (H-H)	10 - 90 %
Volume control	Digital
Display diagonal	2.3 \
Display resolution	132 x 64 pixels
Lines quantity	3 lines
Phonebook capacity	1000 entries
Number of VoIP accounts	3
Number of handles included	1 pc(s)

Weight and Dimensions

Depth	175 mm
Width	212 mm
Height	54 mm