Bosch Solution 6000-IP User Manual

11Bosch Security Systems 10/22 BLCC615U
Solution 6000-IP User Guide
Duress or Silent Alarms
A Duress or Silent Panic alarm can be easily triggered via
the keypad if you are being forced to operate the system
against your will.
To trigger a duress, enter your normal user PIN followed by
the last 2 digits of your user PIN followed by the ON or OFF
key. See the following examples.
1. If your PIN is 2580, to send a duress report when the
area is off, Enter, [2] + [5] + [8] + [0] + [8] + [0] + [OK]
or [ON].
2. If your PIN is 2580, to send a duress report when
the area is on, Enter, [2] + [5] + [8] + [0] + [8] + [0] +
[OFF].
i
Note
Duress alarms are triggered by entering the user PIN
followed by the last 2 digits of the user PIN followed
by the ON or OFF key.
System Programming
i
Note
Some of the examples shown in the following section
assume that you are already in programming
mode. To enter programming mode simply enter
your PIN and press the MENU key on the keypad.
Access > Commands >
Erase User
MENU 1-0-0
This menu allows the installer or master user, to erase
another user. When a user is erased, it will return back to
factory default all information relating to the following:
 PIN
 Token ID
 RF Keyfob ID
 Fingerprint ID
 Name
 TimeZone Access
 Door Assignment
 Area Assignment
Enter [MENU] + [1] + [0] + [0].
1. Use the arrow keys to highlight the user to be erased
then press [OK].
Ur1 John Smith
Ur2 Debbie Smith
Ur3 User 3 Name
Press  OK or MENU
2. Verify the user name to be erased and press [OK].
To abort press [MENU].
To erase Ur1
John Smith
press OK.
Press OK or MENU
PIN Numbers
Access > PIN Codes >
Change Own PIN
MENU 1-1-0
This menu lets you change your own PIN. It is recommended
that you write down your old PIN and the new one before
you begin. The new PIN must have the same number of
digits as your old PIN unless your installer has enabled the
variable length PIN option. Once the change is complete
you should destroy the written copy.
At factory default, each PIN is fixed to 4 digits in length.
The default PIN for User 1 (Master user) is 2580. Only the
security installer can change the PIN length.
Enter programming mode (PIN + MENU) then,
1. Ensure that the system (or area) is turned off.
2. Enter your PIN, and then press [MENU] + [1] + [1] +
[0]. The keypad will prompt you to enter a new PIN.
Enter New PIN For Ur2
Debbie Smith
Press OK or MENU
3. Enter your new PIN, and then press [OK]. If an error
tone sounds, try a different PIN. The keypad will
now prompt you to enter your new PIN again.
Conrm New PIN Ur2
Debbie Smith
Press OK or MENU
4. Enter your new PIN again.
5. Press [OK] to save and exit, or press [MENU] to exit
without saving your PIN has now been changed.
Access > PIN Codes >
Change Other PIN
MENU 1-1-1
If you have a master PIN, this menu allows you to change
somebody else’s PIN. It is recommended that you write
down the old PIN and the new one before you begin. Once
the change is complete you should destroy the written
copy. The new PIN must have the same number of digits
as the old PIN.
At factory default, each PIN is fixed to 4 digits in length.
The default PIN for User 1 (Master user) is 2580.
Enter programming mode (PIN + MENU) then,

Bosch Solution 6000-IP Specifications

General

Brand	Bosch
Model	Solution 6000-IP
Category	Security System
Language	English