Bosch Solution 6000-IP User Manual

9Bosch Security Systems 10/22 BLCC615U
Solution 6000-IP User Guide
Error
Tone
If you enter an incorrect value when
programming, the keypad will sound a 2
second tone.
Menu
Mode
The keypad will sound a Lo/Hi tone to
indicate you have entered MENU Mode and
a Hi/Lo tone to indicate you have exited
MENU mode.
Chime
Tone
The keypad sounds fast short beeps to alert
you when a zone programmed for chime is
faulted or unsealled.
Table 4: Keypad Tones and Their Meanings
Figure 2: CP736B Graphic Keypad
Basic System Operation
Turning An Area All On
Use this function to turn an area All On. The control panel
is factory defaulted for one area. As soon as you turn an
area on, exit time will start. Exit time allows you to exit
the premises without sounding an alarm. Your security
company or a master PIN user can program the length of
exit delay time.
1. Make sure that all zones are normal (not faulted).
2. Enter your PIN, then press the [ON] key.
If your PIN is valid and if all zones are normal, exit delay
time will start. You should leave now. If your control
panel detects a faulted zone, you should return it to
normal, or bypass the zone.
During exit delay, you may stop the area from turning
on by entering your PIN followed by the [OFF] key.
3. To turn the system (or area) off, enter your PIN, then
press [OFF].
Turning An Area Part On / Part 2 On
Use this function to turn an area Part On or Part 2 On. The
control panel is factory default only for one area. Part On
and Part 2 On turns on only part of the area, leaving the
rest of the area turned off.
Only the security company can program which zones are
monitored for Part On. A master user can program which
zones are monitored when a user turns an area Part 2 On.
Once you have turned an area Part On or Part 2 On, exit
delay time starts to count down. You should leave all zones
that are active before exit delay time expires. Leaving
active zones after exit delay expires causes an alarm event.
Use Part On or Part 2 On only when you want part of an
area turned on.
1. Make sure that all zones are normal (not faulted).
2. Enter your PIN, then press the [PART] key.
If your PIN is valid and if all zones are normal, the
keypad will prompt you to select Part On or Part 2 On.
3. Using the arrow keys, highlight Part On or Part 2 On
then press [OK].
Exit delay time will start. You should leave now. If
your system has a faulted zone, you should return it to
normal, or bypass the faulted zone.
During exit delay, you may stop the system from
turning Part On by entering your PIN followed by the
[OFF] key.
4. When exit time has expired, the keypad will display
the Part On icon.
5. To turn the system off, enter your PIN, then press
[OFF].
Turning The System Off
When the system is on, you must enter through a designated
entry door to prevent an alarm. Opening a designated door
(e.g. front door) will start entry time. During entry time, the
keypad will sound the Hi/Lo tone to remind you to turn the
system off. To turn off, enter your PIN followed by the [OFF]
key before the entry delay time expires.
If you enter through the wrong door or fail to turn the
system off before the entry delay time expires, you may
cause a false alarm. If this situation arrises, silence the
alarm by entering your PIN followed by the [OFF] key and
call your security company to let them know that it is not
an emergency situation.
1. Enter your PIN + [OFF] to turn the system (or area)
off. The keypad will no longer display the ‘Lock’ or
‘Part’ icons.

Bosch Solution 6000-IP Specifications

General

Brand	Bosch
Model	Solution 6000-IP
Category	Security System
Language	English