EasyManuals Logo
Home>Cisco>Network Router>CRS-1 - Carrier Routing System Router

Cisco CRS-1 - Carrier Routing System Router Hardware Installation Guide

Cisco CRS-1 - Carrier Routing System Router
104 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #37 background imageLoading...
Page #37 background image
3-11
Cisco CRS-1 Carrier Routing System SIP and SPA Hardware Installation Guide
OL-17439-01
Chapter 3 Overview: Cisco CRS-1 Shared Port Adapters
4-Port OC-3c/STM-1 POS SPA Overview
Table 3-5 describes the 4-Port OC-3c/STM-1 POS SPA LEDs.
4-Port OC-3c/STM-1 POS SPA Interface Specifications
The framer processes incoming and outgoing SONET or SDH frames. The framer operates at
OC-3c/STM-1 line rates (155.52 Mbps).
Packet data is transported with a user-configured encapsul
ation (such as Point-to-Point Protocol [PPP])
and is mapped into the STS-3c/STM-1 frame.
The 4-Port OC-3c/STM-1 POS SPA interface c
omplies with the following RFCs:
RFC 1662, PPP in HDLC-like Framing
RFC 2427, Multiprotocol Interconnect over Frame Relay
RFC 2615, PPP over SONET/SDH
4-Port OC-3c/STM-1 POS SPA Optical Transceiver Modules and Cables
The 4-Port OC-3c/STM-1 POS SPA uses a small form-factor pluggable (SFP) optical transceiver module
installed in each port for SONET and SDH single-mode and multimode optical fiber connection (see
Figure 3-9).
Cisco Systems qualifies the optics that are appro
ved for use with its SPAs. The 4-Port OC-3c/STM-1
POS SPA supports the following types of optical transceiver modules:
Multimode (MM) SFP module—SFP-OC3-MM
Short-reach (SR) SFP module—SFP-OC3-SR
Intermediate-reach (IR) SFP module (15 km)—SFP-OC3-IR1
Long-reach (LR) SFP module (40 km)—SFP-OC3-LR1
Long-reach (LR) SFP module (80 km)—SFP-OC3-LR2
Ta b l e 3-5 4-Port OC-3c/STM-1 POS SPA LEDs
LED Label Color State Meaning
C/A Off Off SONET controller is shut down.
Green On Port is enabled by software, and there is a v
alid SONET signal
without any alarms.
Amber On Port is enabled by software, and there is at le
ast one alarm.
A/L Off Off Interface is shut down.
Green On Port is enabled by software, an
d loopback is off.
Amber On Port is enabled by software, and loopback is on.
STATUS Off Off SPA power is off.
Green On SPA is ready and operational.
Amber On SPA power is on and good, and the SPA is being configured.

Table of Contents

Other manuals for Cisco CRS-1 - Carrier Routing System Router

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco CRS-1 - Carrier Routing System Router and is the answer not in the manual?

Cisco CRS-1 - Carrier Routing System Router Specifications

General IconGeneral
BrandCisco
ModelCRS-1 - Carrier Routing System Router
CategoryNetwork Router
LanguageEnglish

Related product manuals