CommScope CAP MX Series User Manual

M0201ANC_uc CommScope Era
™
Fiber Low Power Carrier Access Point Installation Guide
© June 2019 CommScope, Inc. Page 15
Plan and Prepare for a Fiber CAP L Installation
other antenna or transmitter. Users and installers must be provided with antenna installation
instructions and transmitter operating conditions for satisfying RF exposure compliance.
French:
Cet appareil est conforme a F
CC Partie15. Son utilisation est soumise a Les deux conditions suivantes: (1)
cet appareil ne peut pas provoquer d'interferences et (2) cet appareil doit accepter Toute interference, y
compris les interferences qui peuvent causer un mauvais fonctionnement du dispositif.
Cet appareil est conforme avec Sante Ca
nada Code de securite 6. Le programme d'installation de cet
appareil doit s'assurer que les rayonnements RF n'est pas emis au-dela de I'exigence de Sante Canada. Les
informations peuvent etre obtenues:
http://www.hc-sc.gc.ca/ewh-semt/pu
bs/radiation/radio_guide-lignes_direct-eng.php
Les changements ou modifications non expressement approuves par la par
tie responsable de la
conformite pourraient annuler l'autorite de l'utilisateur a utiliser cet equipement.
AntenneStmtpo
urISDE:
Ce dispositif a ete desi
gne pour fonctionner avec les antennes ayant un gain maximal de 9 dBi. Antennes
ayant un gain plus grand que 9 dBi sont interdites pour une utilisation avec cet appareil sans le
consentement des organismes de reglementation d'ISDE. L'impedance d'antenne requise est 50 ohms.
L'antenne (s) utilise
pour cet emetteur doit etre installe pour fournir une distance de separation minimale
(comme indique dans le Table 6) par rapport a tou
te personnes et ne doit pas etre co-localisees ou
operant en conjonction avec une autre antenn
e ou emetteur. Les utilisateurs et les installateurs doivent
etre fournis avec des instructions d'installation de l'antenne et des conditions de fonctionnement de
l'emetteur pour satisfaire la conformite aux expositions RF.
5 Noti
ce: The unit complies with Overvoltage Category II. It also complies with the surge requirement
according to EN 61000-4-5 (fine protection); however, installation of an additional medium (via local
supply connection) and/or coarse protection (external surge protection) is recommended depending on
the individual application in order to avoid damage caused by overcurrent.
For Canada and US, components used to
reduce the Overvoltage Category shall comply with the
requirements of IEC 61643-series. As an alternative, components used to reduce the Overvoltage
Category may comply with ANSI/IEEE C62.11, CSA Certification Notice No. 516, CSA C22.2 No. 1, or UL
1449. Suitability of the component for the application shall be determined for the intended installation.
6 Noti
ce: Corresponding local particularities and regulations must be observed. For national deviations,
please refer to the respective documents included in the manual CD that is delivered with the unit.
7 Note:For a Class
B digital device or peripheral:
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relo
cate the receiving antenna.
• I
ncrease the separation between the equipment and receiver.
• C
onnect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consul
t the dealer or an experienced RF technician for help.

CommScope CAP MX Series Specifications

General

Brand	CommScope
Model	CAP MX Series
Category	Wireless Access Point
Language	English