EasyManuals Logo
Home>Danfoss>DC Drives>VLT 5003

Danfoss VLT 5003 User Manual

Danfoss VLT 5003
240 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #29 background imageLoading...
Page #29 background image
Compact, AC line supply 3 x 525-600 V
According to international requirements VLT type 5032 5042 5052 5062
Normal overload torque (110 %):
Output current
I
VLT,N
[A] (550 V)
43 54 65 81
I
VLT, MAX
(60 s) [A] (550 V)
47
59 72 89
I
VLT,N
[A] (575 V)
41
52 62 77
I
VLT, MAX
(60 s) [A] (575 V)
45
57 68 85
Output
S
VLT,N
[kVA] (550 V)
41 51 62 77
S
VLT,N
[kVA] (575 V)
41
52 62 77
Typical shaft output
P
VLT,N
[kW]
30 37 45 55
Typical shaft output
P
VLT,N
[HP]
40 50 60 75
High overload torque (160 %):
Output current
I
VLT,N
[A] (550 V)
34 43 54 65
I
VLT, MAX
(60 s) [A] (550 V)
54
69 86 104
I
VLT,N
[A] (575 V)
32
41 52 62
I
VLT, MAX
(60 s) [A] (575 V)
51
66 83 99
Output
S
VLT,N
[kVA] (550 V)
32 41 51 62
S
VLT,N
[kVA] (575 V)
32
41 52 62
Typical shaft output
P
VLT,N
[kW]
22 30 37 45
Typical shaft output
P
VLT,N
[HP]
30 40 50 60
Max. cable cross-section to motor, 35 50 50 50
brake and load sharing [mm
2
]/[AWG]
2) 5)
2 1/0 1/0 1/0
Min. cable cross-section to motor, 10 16 16 16
brake and load sharing [mm
2
]/[AWG]
4)
8 6 6 6
Normal overload torque (110 %):
Rated input current
I
L,N
[A] (550 V)
42 53 63 79
I
L,N
[A] (600 V)
38 49 58 72
High overload torque (160 %):
Rated input current
I
L,N
[A] (550 V)
33 42 53 63
I
L,N
[A] (600 V)
30 38 49 58
Max. cable cross-section 35 50 50 50
power[mm
2
]/[AWG]
2) 5)
2 1/0 1/0 1/0
Max. pre-fuses
[-]/UL
1)
[A]
60 75 90 100
Efficiency
3)
0.96 0.96 0.96 0.96
Weight IP 20 EB [kg] 30 48 48 48
Power loss at max. load [W] 1074 1362 1624 2016
Enclosure IP 20/Nema 1
1. For type of fuse, see section Fuses.
2. American Wire Gauge.
3. Measured using 100 ft [30 m] shielded motor cables at rated load and rated frequency.
4. Min. cable cross-section is the smallest cable cross-section allowed to be fitted on the terminals to comply with IP 20. Always comply
with national and local regulations on min. cable cross-section.
5. Aluminum cables with cross-section above 0.054 in
2
[35 mm
2
] must be connected by use of an AI-Cu connector.
VLT
®
5000 Series
26 MG.51.C5.22 - VLT
p
is a registered Danfoss trademark.

Table of Contents

Other manuals for Danfoss VLT 5003

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Danfoss VLT 5003 and is the answer not in the manual?

Danfoss VLT 5003 Specifications

General IconGeneral
BrandDanfoss
ModelVLT 5003
CategoryDC Drives
LanguageEnglish

Related product manuals