Danfoss VLT Midi Drive FC 280 Programming Guide

4.16 Parameters: 16-** Data Readouts
16-00 Control Word
Range: Function:
0* [0 - 65535 ] View the control word sent from the frequency
converter via the serial communication port in
hex code.
16-01 Reference [Unit]
Range: Function:
0 ReferenceFeed-
backUnit*
[-4999 - 4999
ReferenceFeed-
backUnit]
View the present reference
value applied on impulse
or analog basis in the unit
resulting from the congu-
ration selected in
parameter 1-00 Congu-
ration Mode.
16-02 Reference [%]
Range: Function:
0 %* [-200 -
200 %]
View the total reference. The total reference
is the sum of digital, analog, preset, bus,
and freeze references, plus catch up and
slow down.
16-03 Status Word
Range: Function:
0* [0 - 65535 ] View the status word sent from the frequency
converter via the serial communication port in
hex code.
16-05 Main Actual Value [%]
Range: Function:
0 %* [-200 - 200 %] View the 2-byte word sent with the status
word to the bus master reporting the
main actual value.
16-09 Custom Readout
Range: Function:
0 CustomRea-
doutUnit*
[0 - 9999
CustomRea-
doutUnit]
View the custom readout from
parameter 0-30 Custom
Readout Unit to
parameter 0-32 Custom
Readout Max Value.
16-10 Power [kW]
Range: Function:
0 kW* [0 -
1000
kW]
Shows motor power in kW. The calculated
value shown is based on the actual motor
voltage and motor current. The value is ltered,
and therefore approximately 30 ms may pass
from when an input value changes to when
the data readout values change. The resolution
of readout value on eldbus is in 10 W steps.
16-11 Power [hp]
Range: Function:
0 hp* [0 -
1000 hp]
View the motor power in hp. The value shown
is calculated on the basis of the actual motor
voltage and motor current. The value is
ltered, and therefore approximately 30 ms
may pass from when an input value changes
to when the data readout values change.
16-12 Motor Voltage
Range: Function:
0 V* [0 - 65535 V] View the motor voltage, a calculated value
is used for controlling the motor.
16-13 Frequency
Range: Function:
0 Hz* [0 - 6553.5 Hz] View the motor frequency, without
resonance dampening.
16-14 Motor current
Range: Function:
0 A* [0 - 655.35
A]
View the motor current measured as an
average value, I
RMS
. The value is ltered, and
approximately 30 ms may pass from when
an input value changes to when the data
readout values change.
16-15 Frequency [%]
Range: Function:
0 %* [0 -
6553.5 %]
View a 2-byte word reporting the actual
motor frequency (without resonance
dampening) as a percentage (scale
0000-4000 hex) of parameter 4-19 Max
Output Frequency.
16-16 Torque [Nm]
Range: Function:
0 Nm [-30000 -
30000 Nm]
View the torque value with sign, applied to
the motor shaft. Some motors supply more
than 160% torque. As a result, the minimum
value and the maximum value depend on
the maximum motor current as well as the
motor used.
16-18 Motor Thermal
Range: Function:
0 %* [0 -
100 %]
View the calculated thermal load on the motor.
The cut-out limit is 100%. The basis for
calculation is the ETR function selected in
parameter 1-90 Motor Thermal Protection.
16-20 Motor Angle
Range: Function:
0* [0 - 65535 ]
Parameter Descriptions Programming Guide
MG07C102 Danfoss A/S © 12/2015 All rights reserved. 99
4 4

Danfoss VLT Midi Drive FC 280 Specifications

General

Brand	Danfoss
Model	VLT Midi Drive FC 280
Category	DC Drives
Language	English