Danfoss VLT Midi Drive FC 280 Programming Guide

4.12 Parameters: 12-** Ethernet
12-00 IP Address Assignment
Option: Function:
[0] MANUAL Set the IP address in parameter 12-01 IP
Address.
[1] DHCP IP address is assigned via DHCP server.
[2] BOOTP IP address is assigned via BOOTP server.
[10] * DCP
[20] From node ID
12-01 IP Address
Range: Function:
0* [0 -
4294967295 ]
Congure the IP address of the option.
Read-only if parameter 12-00 IP Address
Assignment is set to [1] DHCP, [2] BOOTP,
or via DIP switches.
12-02 Subnet Mask
Range: Function:
0* [0 -
4244635647 ]
Congure the IP subnet mask of the
option. Read-only if parameter 12-00 IP
Address Assignment is set to [1] DHCP or
[2] BOOTP.
12-03 Default Gateway
Range: Function:
0* [0 -
2147483647 ]
Congure the IP default gateway of the
option. Read-only if parameter 12-00 IP
Address Assignment set to [1] DHCP or [2]
BOOTP.
12-04 DHCP Server
Range: Function:
0* [0 - 2147483647 ]
NOTICE
A power cycle is necessary after
setting the IP parameters manually.
Read only. Displays the IP address of the
found DHCP or BOOTP server.
12-05 Lease Expires
Range: Function:
0* [0 - 4294967295 ] Read only. Shows the lease time left for
the current DHCP-assigned IP address.
12-06 Name Servers
Range: Function:
0* [0 - 2147483647] IP addresses of domain name servers. Can
be automatically assigned when using
DHCP.
12-07 Domain Name
Range: Function:
0* [0–48 ] Domain name of the attached network. Can be
automatically assigned when using DHCP network.
12-08 Host Name
Range: Function:
0* [0–48 ] Logical (given) name of option.
12-09 Physical Address
Range: Function:
0* [0–17 ] Read only.
Shows the physical (MAC) address of the option.
12-10 Link Status
Option: Function:
[0] * No Link
[1] Link Shows the link status of the Ethernet ports.
12-11 Link Duration
Range: Function:
Size related* [ 0 - 0 ] Shows the duration of the present link
on each port in dd:hh:mm:ss.
12-12 Auto Negotiation
Option: Function:
Congures auto negotiation of Ethernet link
parameters, for each port: ON or OFF.
[0] O Link speed and link duplex can be congured in
parameter 12-13 Link Speed and parameter 12-14 Link
Duplex.
[1] * On
12-13 Link Speed
Option: Function:
Forces the link speed for each port in 10 Mbps
or 100 Mbps. If parameter 12-12 Auto Negotiation
is set to [1] On, this parameter is read-only and
shows the actual link speed. If no link is present,
None is shown.
[0] * None
[1] 10 Mbps
[2] 100
Mbps
12-14 Link Duplex
Option: Function:
Forces the duplex for each port to full or half
duplex. If parameter 12-12 Auto Negotiation is
set to [1] On, this parameter is read-only.
[0] Half Duplex
[1] * Full Duplex
Parameter Descriptions
VLT
®
Midi Drive FC 280
82 Danfoss A/S © 12/2015 All rights reserved. MG07C102
44

Danfoss VLT Midi Drive FC 280 Specifications

General

Brand	Danfoss
Model	VLT Midi Drive FC 280
Category	DC Drives
Language	English