EasyManuals Logo
Home>Dell>Desktop>OptiPlex 960

Dell OptiPlex 960 User Manual

Dell OptiPlex 960
146 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #27 background imageLoading...
Page #27 background image
Replacing Drive Bay Inserts
If you are removing a drive, and need to replace the inserts:
1. At the front of the bezel, place the plastic insert over the drive bay opening and insert the tabs at the right edge of the insert into the slots at the right
side of the drive bay opening.
2. Swing the left side of the insert into the opening until it snaps into place.
3. Perform the procedure After Working on Your Computer.
Optical Drive
Removing an Optical Drive
1. Perform the procedure Before Working on Your Computer.
2. Lift the drive-release latch and slide the drive towards the back of the computer. Then lift it out of the computer.
1
retention tab
2
drive bay insert
CAUTION: Before you begin any of the procedures in this section, read the safety information that shipped with your computer. For additional
safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
CAUTION: To guard against electrical shock, always unplug your computer from the electrical outlet before removing the computer cover.
NOTE: If you will be operating your computer without an optical drive or a 3.5-inch device (floppy drive or media card reader) installed, the appropriate
drive bay insert must be installed in place of the drive. Contact Dell if you need a drive bay insert. See Removing Drive Bay Inserts.
NOTICE: Do not pull the drive out of the computer by the drive cables. Doing so may cause damage to cables and the cable connectors.
1
drive release latch
2
optical drive

Table of Contents

Other manuals for Dell OptiPlex 960

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Dell OptiPlex 960 and is the answer not in the manual?

Dell OptiPlex 960 Specifications

General IconGeneral
Tcase72.4 °C
Bus typeFSB
SteppingE0
Processor cache6 MB
Processor cores2
Processor modelE8400
System bus rate- GT/s
Processor familyIntel® Core™2 Duo
Processor seriesIntel Core 2 Duo E8000 Series
Processor socketLGA 775 (Socket T)
Processor codenameWolfdale
Processing Die size107 mm²
Processor frequency3 GHz
Processor cache typeL2
Processor lithography45 nm
Processor manufacturerIntel
Processor front side bus1333 MHz
Processor operating modes64-bit
ECC supported by processorNo
Thermal Design Power (TDP)65 W
Number of processors installed1
CPU multiplier (bus/core ratio)9
Number of Processing Die Transistors410 M
Internal memory4 GB
Memory clock speed800 MHz
Internal memory typeDDR2-SDRAM
Maximum internal memory16 GB
Memory layout (slots x size)2 x 2 GB
HDD speed7200 RPM
HDD interfaceSATA
Optical drive typeDVD-RW
Total storage capacity250 GB
Networking featuresGigabit Ethernet
Graphics card familyAMD
Compliance industry standardsIEEE 802.3, IEEE 802.3u, IEEE 802.3ab
Discrete graphics card modelAMD Radeon HD 3470
Maximum graphics card memory- GB
On-board graphics card modelNot available
Discrete graphics card memory256 GB
Operating system installedWindows 7 Professional
Microphone inYes
USB 2.0 ports quantity10
Firewire (IEEE 1394) ports0
Ethernet LAN data rates10, 100, 1000 Mbit/s
Chassis typeSFF
Product colorBlack
Product typePC
Processor codeSLB9J
Processor ARK ID33910
Processor package size37.5 x 37.5 mm
Weight and Dimensions IconWeight and Dimensions
Depth323 mm
Width85 mm
Height289 mm
Weight5900 g

Related product manuals