Denon AVR-X4000 User Manual

181
Appendix
TipsPlaybackConnections
Contents
Front panel Display Rear panel IndexRemote
Settings
Manual Setup
Perform when setting the speakers manually or when changing settings
made in Audyssey® Setup.
•If you change the speaker settings after performing Audyssey® Setup,
it will not be possible to select Audyssey MultEQ® XT32, Audyssey
Dynamic EQ® and Audyssey Dynamic Volume® (vpage156, 158).
•“Manual Setup” can be used without changing the settings. Please set
if necessary.
Amp Assign
Select power amplifier usage method to match your speaker system.
2 Assign Mode
Set the assignment mode.
7.1ch(SB/FH/FW) : Assigns all power amplifiers within this unit for
MAIN ZONE.
5.1ch + ZONE2 (Default) : Setting to assign the unit’s built-in power
amplifier for ZONE2 and output the audio in
stereo.
5.1ch + ZONE3 : Setting to assign the unit’s built-in power amplifier for
ZONE3 and output the audio in stereo.
5.1ch + ZONE2/3-MONO : Setting to assign the unit’s built-in power
amplifier for ZONE2 and ZONE3 and
output the audio in monaural.
5.1ch(Bi-Amp) : Setting to use the front speakers via the bi-amp
connection.
5.1ch + Front B : Setting to use the second set of front speakers for
playback. You can switch the front speakers A and
B to be used for playback in accordance with the
2-channel playback or multi-channel playback mode.
When you select this setting, also perform the
“Front Speaker Setup” (vpage187) procedure.
7.1ch/2ch Front : Setting to use the other front speakers for playback
when you do 2-channel playback in DIRECT or
STEREO mode. When you select this setting, also
perform the “Front Speaker Setup” (vpage187)
procedure.
9.1ch(SB/FH/FW) : Setting to use a maximum 9.1 channel speaker
system by using a combination of the unit’s
7-channel built-in amp with an external power amp
connected to a set of 2-channel speakers.

Denon AVR-X4000 Specifications

General

Receiver type	-
Frequency range	10 - 100000 Hz
Output impedance	16 Ω
Speaker selector	A+B
Input sensitivity	200 mV
Audio output channels	7.2 channels
Signal-to-Noise Ratio (SNR)	102 dB
Total Harmonic Distortion (THD)	0.008 %
Power output per channel (1KHz@6 Ohm)	165 W
Power output per channel (20-20KHz@8 Ohm)	125 W
HDMI in	7
AC (power) in	Yes
Composite video in	4
Ethernet LAN (RJ-45) ports	1
Component video (YPbPr/YCbCr) in	2
Number of HDMI outputs	3
Connectivity technology	Wired
Speakers connectivity type	Banana connector
Audio formats supported	AAC, FLAC, MP3, WAV, WMA
Image formats supported	JPG
Wi-Fi	No
RDS features	PTY, TP
FM band range	87.5 - 108 MHz
Supported radio bands	FM
Internet radio services supported	Spotify, vTuner
Supported video modes	1080i, 1080p, 480p, 576p, 720p
Display	VFL
Color depth	24 bit
Aspect ratio	4:3, 16:9
Product color	Silver
Audio decoders	Dolby Digital, Dolby Digital EX, Dolby Digital Plus, Dolby Pro Logic II, Dolby Pro Logic IIx, Dolby Pro Logic IIz, Dolby TrueHD, DTS-ES (Discrete 6.1), DTS-ES (Matrix 6.1), DTS-HD, DTS-HD Master Audio
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Apple docking compatibility	Not supported
AC input voltage	230 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	0.1 W
Power consumption (typical)	670 W

Weight and Dimensions

Depth	379 mm
Width	434 mm
Height	167 mm
Weight	12300 g