ConnectCore for i.MX51
©2011DigiInternational,Inc. 21
153 GPOIO18 EIM_D26/KEY_COL7/
UART3_TXD/
UART2_RTS#/
CMPOUT2/TRACE10
i.MX51: EIM_D26
ETH_CTRL: D10
Peripheral Application Data
154 GPOIO18 EIM_D27/GPIO2_9/
UART3_RTS#/I2C2_SCL/
AUD6_RXC/TRACE11
i.MX51: EIM_D27
ETH_CTRL: D11
Peripheral Application Data
155 - GND - -
156 GPOIO18 EIM_D29/KEY_ROW5/
SISG1/AUD6_RXD/
TRACE13
i.MX51: EIM_D29
ETH_CTRL: D13
Peripheral Application Data
157 GPOIO18 EIM_D28/KEY_ROW4/
SISG0/AUD6_TXD/
TRACE12
i.MX51: EIM_D28
ETH_CTRL: D12
Peripheral Application Data
158 GPOIO18 EIM_D31/KEY_ROW7/
SISG03/AUD6_TXFS/
TRACE15
i.MX51: EIM_D31
ETH_CTRL: D15
Peripheral Application Data
159 GPOIO18 EIM_D30/KEY_ROW6/
SISG2/AUD6_TXC/
TRACE14
i.MX51: EIM_D30
ETH_CTRL: D14
Peripheral Application Data
160 GPOIO18 EIM_A17/GPIO2_11 i.MX51: EIM_A17 Not used
161 GPOIO18 EIM_A16/GPIO2_10 i.MX51: EIM_A16 Not used
162 GPOIO18 EIM_A19/GPIO2_13 i.MX51: EIM_A19 Not used
163 GPOIO18 EIM_A18/GPIO2_12 i.MX51: EIM_A18 Not used
164 GPOIO18 EIM_A21/GPIO2_15 i.MX51: EIM_A21 Boot Configuration Switch
165 GPOIO18 EIM_A20/GPIO2_14 i.MX51: EIM_A20 Boot Configuration Switch
166 GPOIO18 EIM_A23/GPIO2_17 i.MX51: EIM_A23 Not used
167 GPOIO18 EIM_A22/GPIO2_16 i.MX51: EIM_A22 Not used
168 GPOIO18 EIM_A25/GPIO2_19/
USBH2_DIR/DI1_PIN4
i.MX51: EIM_A25 Not used
169 GPOIO18 EIM_A24/GPIO2_18/
USBH2_CLK
i.MX51: EIM_A24 Not used
170 GPOIO18 EIM_A27/GPIO2_21/
USBH2_NXT/SISG1/
CSI2_DATA_EN/
DI1_PIN1
i.MX51: EIM_A27 XBEE_SLEEP_RQ
171 GPOIO18 EIM_A26/GPIO2_20/
USBH2_STP/SISG0/
CSI1_DATA_EN/
DI2_EXT_CLK
i.MX51: EIM_A26 Not used
172 GPOIO18 EIM_OE#/GPIO2_24 i.MX51: EIM_OE
ETH_CTRL: RD#
Peripheral Application Output
Enable
Pin I/O Type Signal name Use on module Use on development board Comments
Downloaded from Elcodis.com electronic components distributor
To Next Page
Loading...
Need help?
General
