Hayward H150FD Service & Installation Manual

Pomona, CA Clemmons, NC Nashville, TN
Tel: 908-351-5400 www.haywardpool.com
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
12
 'RQRWLQVWDOOZLWKLQ´RIDQ\RXWGRRU
+9$&HTXLSPHQW
7. Do not install where water may run-off a
roof into the heater. A gutter may be needed
to protect the heater.
8. Any enclosure around the heater must
provide a combustion air vent commencing
within 12 inches of the bottom of the enclo-
sure. The vent opening shall have a mini-
mum free area of 1 square inch per 4,000
EWXKULQSXWUDWLQJRIDOOJDVDSSOLDQFHVLQWKHHQFORVXUH6HH7DEOH
3$##/A&B]
7KLVKHDWHUPD\EHLQVWDOOHGRQHLWKHUQRQFRPEXVWLEOHRUFRPEXVWLEOHÀRRULQJ8OWUDOLWHRUHTXLYDOHQW
FRQFUHWHRYHUIRDP+9$&SDGVDUHDFFHSWDEOH
+A.N'#V&!-/%:\.+(]
The heater is equipped for installation of factory-supplied tie-down brackets if required by local codes.
The brackets are shipped in the consumer kit. You will need the following to complete the installation:
1. Tie-down brackets ()$&725<6833/,(', quantity = 4)
2. Sheet metal screws ()$&725< 6833/,(', quantity = 4)
 &RQFUHWHWDSSLQJVFUHZVWDSFRQV¿HOGVXSSOLHGTXDQWLW\ VL]HWREHó´GLDPHWHUZLWKD
 PLQLPXPOHQJWKRI´
A&(+%$$A&B!+A.N'#V&!-/%:\.+(]
1. Locate the tie-down brackets and the sheet metal screws.
 2EWDLQWKHWDSFRQV%HVXUHWKHRYHUDOOOHQJWKRIWKHFRQFUHWHWDSSLQJVFUHZLVDWOHDVW´
3. Remove the front access panel (4 screws).
4. Remove the rear access panel (4 screws).
5. Position the heater on the pad so that all tap-
FRQVFDQ³ELWH´LQWRWKHSDG2EVHUYHORFDOFRGHV
regarding pad construction, some jurisdictions
specify a minimum thickness for concrete pads.
6. Slip the tie-down brackets into the slots in the
front of the heater base pan from underside of
the heater, so that they are positioned as shown
LQ¿JXUH,QVWDOOWKHVKHHWPHWDOVFUHZVWKURXJK
the holes in the bracket to secure the bracket to
the heater base pan.
7. Install the tap-cons through the holes in the tie-
down brackets into the pad.
8. Repeat Steps 6 & 7 at the rear of the heater.
 ,QVWDOODWLRQLVFRPSOHWHGZKHQEUDFNHWVDUH
secured to the heater and the pad. Install the ac-
cess panels when complete.
Equipment pad
Install sheet metal screws (supplied) at
these locations (front and rear)
,QVWDOOFRQFUHWHWDSSLQJVFUHZV¿HOGVXSSOLHG
at these locations (front and rear)
Figure 3
+DSE;!5
#O=^??C!A@J=DEED=>?@!:E;DCD@<;J
Heater Panel Required Clearance
Top Unobstructed
Front 24 inches
Back 6 inches
Water Connection Side 12 inches
Side Opposite Water Connection 6 inches

Hayward H150FD Specifications

General

Brand	Hayward
Model	H150FD
Category	Swimming Pool Heater
Language	English