JVC DR-MV1 User Manual

Masterpage:Right0
EN 17
Filename [DR-MV1SE_04Name.fm]
Page 17 March 11, 2004 7:27 pm
INITIAL SETTINGS
Auto Channel Set/Auto Clock Set/Auto Guide Program
Number Set
1 Press 1 to turn on the unit. The Country Set display appears
on the TV screen.
2 Press rt w e to select your
country’s name, then press
ENTER. The Language Set
display appears on the TV screen.
NOTES:
● If you have selected BELGIUM or
SUISSE, go to step 3.
● If you have selected
MAGYARORSZÁG, CESKÁ
REPUBLIKA, POLSKA or OTHER EASTERN, press ENTER. The
Clock Set screen appears. Set the clock manually (
墌 pg. 85), then
go to step 4.
● If you have selected any other country name, go to step 4.
3 Press rt w e to select the
language of your choice, then
press ENTER. The AUTO SET/
T-V LINK display appears on the
TV screen.
4 Press rt to select “AUTO
SET”, then press ENTER. The
AUTO SET screen will appear.
A
TTENTION:
“AUTO” blinks on the front display
panel; do NOT press any button on
the unit or remote control until the
front display panel shows “– –:– –”
as illustrated on page 19.
● When you have connected the unit
to a TV offering T-V Link via a
fully-wired 21-pin SCART cable
(
墌 pg. 16) and the TV is turned
on, the unit automatically performs
the Preset Download (
墌 pg. 18) even if you select “AUTO SET” for
Auto Set Up function.
NOTES:
● In areas where no TV station transmits a PDC (Programme Delivery
Control) signal, the unit can perform neither Auto Clock Set nor Auto
Guide Program Number Set.
● If there is a power cut, or if you press 1 or SET UP while Auto Set
Up is in progress, Auto Set Up will be interrupted; be sure to turn off
the unit power once and try again from step 1.
● Auto Clock Set may not function properly depending on the reception
condition.
● If no sound accompanies the picture or the audio sounds unnatural
on some channels that have been stored by Auto Set Up, the TV
system setting for those channels may be incorrect. Select the
appropriate TV system for those channels. (
墌 pg. 84,
“INFORMATION”)
Auto Set Up
After the 1 button on the unit remote control is pressed for the
first time to turn on the unit, by simply selecting your country*,
the Auto Set Up function sets the tuner channels, clock** and
Guide Program numbers automatically.
* If you live in Belgium (BELGIUM) or Switzerland (SUISSE), you also
need to select your language.
** If you live in Hungary (MAGYARORSZÁG), Czech Republic (
C ESKÁ
REPUBLIKA), Poland (POLSKA) or other countries in Eastern Europe
(OTHER EASTERN), set the clock manually.
Before starting, make sure of the following:
● The TV aerial cable should be connected to the unit.
● The unit’s mains power cord should be connected to a mains
outlet.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
1
4
7
2
5
8
0
3
6
9
DISPLAY
8
DISPLAY
8
VCR/DVD
SAT
A
TTENTION:
Once you have performed Auto Set Up, even if the unit’s memory
backup has expired, all the stored stations and their Guide
Program numbers remain in the unit’s memory and the unit will
not perform Auto Set Up again. The unit only performs Auto
Clock Set when the unit is turned on.
If you have moved to a different area, perform each setting as
required.
● Tuner setting (墌 pg. 82)
● Clock setting (
墌 pg. 85)
If a new station starts broadcasting in your area, perform tuner
setting. (墌 pg. 82)
After “Auto Set Up” is completed, perform “Monitor Set (DVD
Deck Only)” on page 23.
DR-MV1SE_00.book Page 17 Thursday, March 11, 2004 7:28 PM

JVC DR-MV1 Specifications

General

Brand	JVC
Model	DR-MV1
Category	DVD VCR Combo
Language	English