Filename [DR-MV1SE_07VCR Operation.fm]
Masterpage:Left+
54 EN
Page 54 March 11, 2004 7:27 pm
OPERATIONS ON VCR DECK
You can programme this unit to timer-record as many as
8 programmes.
With the S
HOWVIEW system, timer programming is greatly
simplified because each TV programme has a corresponding code
number which your unit is able to recognize.
You can use the remote control to enter the
SHOWVIEW number.
1 Load a cassette with the record safety tab intact.
2 Press VCR/DVD repeatedly so that the VCR lamp lights up on
the unit.
3 Press SHOWVIEW to access the SHOWVIEW screen.
4 Press the number keys to enter
the S
HOWVIEW number of a
programme you wish to record, then
press ENTER.
● If you have made a mistake, press
CANCEL (&) and input the correct
number before you press ENTER.
● If the number you entered is invalid,
“ERROR” appears on the TV screen
and “Err” appears on the front display
panel. Press CANCEL (&) and input a valid S
HOWVIEW number.
5 The SHOWVIEW number you
entered and the matching timer-
recording information are displayed on
the TV screen. Check the programme
data.
● To cancel this setting, press
SHOWVIEW or PROG/CHECK.
6 Press REC MODE to select the desired recording mode. Or
press we to select “SP/EP”, then press rt to select the desired
recording mode.
7 Press the number keys to to set “VPS/PDC” to “ON” or “OFF”.
8 Press ENTER to complete timer programming.
● To programme another timer, repeat steps 3 – 8.
● If “PROGRAM OVERLAP” appears on the TV screen, see page 56.
9 Press VCR TIMER (#) to engage the unit’s timer mode. The
VCR timer lamp lights up on the unit and the DVD deck is
automatically selected. When the DVD deck is in timer standby
mode, the unit is automatically turned off.
● To disengage the timer mode, press VCR TIMER (#) again.
NOTES:
● To Timer-Record Weekly Or Daily Serials:
— in step 5, press number key “9” for weekly serials or number key
“8” for daily serials (Monday — Friday). Either “WEEKLY” or “DAILY”
appears on the TV screen. Pressing the button again makes the
corresponding indication disappear.
● You can programme this unit to timer-record as many as 8
programmes. If you try to programme the unit to record a ninth,
“PROGRAMME FULL” appears on the TV screen and “FULL”
appears on the front display panel. To record the extra programme,
you must first cancel any unnecessary programmes. (
墌 pg. 56)
● To record the programmes received by satellite receiver, record on
the DVD discs. For details, refer to “S
HOWVIEW
®
Timer Programming”
(
墌 pg. 43).
SHOWVIEW
®
Timer Programming
● Make sure that the unit’s built-in clock is set properly.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
IMPORTANT:
Make sure the channel position number you wish to record is
displayed; if not, see “S
HOWVIEW
®
System Setup” (墌 pg. 82) and set
the Guide Programme number correctly.
1
4
7
2
5
8
0
3
6
9
0 – 9
RETURN
ENTER
SHOWVIEW
CANCEL
VCR TIMER (#)
VCR/DVD
REC MODE
SAT
SHOWVIEW SYSTEM
IMPORTANT:
If you have moved to a different area or if a broadcasting station's
programme number has been changed, the wrong programme
number will be displayed on the S
HOWVIEW programme screen in
step 5. When this happens, set the correct Guide Programme
number for that station. (
墌 pg. 82, “SHOWVIEW
®
System Setup”)
DR-MV1SE_00.book Page 54 Thursday, March 11, 2004 7:28 PM
To Next Page
Loading...
Need help?
General
