JVC DR-MV1 User Manual

Masterpage:Right+
EN 43
Filename [DR-MV1SE_06DVD Operation2.fm]
Page 43 March 11, 2004 7:27 pm
OPERATIONS ON DVD DECK
You can programme this unit to timer-record as many as
8 programmes.
With the S
HOWVIEW system, timer programming is greatly
simplified because each TV programme has a corresponding code
number which your unit is able to recognize.
You can use the remote control to enter the S
HOWVIEW number.
1 Load a recordable disc.
2 Press VCR/DVD repeatedly so that the DVD lamp lights up on
the unit.
3 Press SHOWVIEW to access the SHOWVIEW screen.
4 Press the number keys to
enter the PlusCode number of a
programme you wish to record,
then press ENTER.
● If you have made a mistake, press
CANCEL (&) and input the correct
number before you press ENTER.
● To clear all entered numbers at a
time, press CLEAR(8).
● If the number you entered is invalid, “SHOWVIEW NO. ERROR
CONFIRM SHOWVIEW NO. THEN RETRY” appears on the TV
screen. Input a valid S
HOWVIEW number.
● If “GUIDE PROGRAM IS NOT SET SELECT CHANNEL YOU WANT
TO RECORD” appears on the TV screen, set Guide Program
numbers manually. (
墌 pg. 82)
● When “PROGRAMME FULL DELETE UNWANTED TIMER
PROGRAMME” appears on the TV screen, you need to cancel some
of the reserved programmes. (
墌 pg. 47)
5 The SHOWVIEW number you entered and the matching timer-
recording information are displayed on the TV screen. Check the
programme data.
● To cancel this setting, press SHOWVIEW or RETURN.
6 Press we to select the desired recording option as required.
Press rt to select the desired setting, then press ENTER.
● “STOP” (To advance/go back the stop time by 30 minutes, press and
hold rt).
● “DAILY/WEEKLY” (
墌 pg. 43, “Daily/Weekly Recording”))
● “REC MODE” (
墌 pg. 40, “Recording Mode”)
● “NAME” (
墌 pg. 59, “Modify Programme Name”)
● “VPS/PDC” (
墌 pg. 44, “VPS/PDC Recording”)
7 Press ENTER to access the Programme Confirmation screen.
8 Press ENTER to complete timer programming.
● To programme another timer, repeat steps 3 – 8.
● If “PROGRAM OVERLAPPED” appears on the TV screen, see
page 47.
9 Press DVD TIMER (#) to engage the unit’s timer mode. The
DVD timer lamp lights up on the unit and the VCR deck is
automatically selected. When the VCR deck is in timer standby
mode, the unit is automatically turned off.
● To disengage the timer mode, press DVD TIMER (#) again.
NOTES:
● There may be cases that SHOWVIEW Timer programming function
prolongs the stop time of the programming.
● When two successive programmes are recorded on a DVD-RW disc
with S
HOWVIEW Timer programming function, the beginning of the
second one may be left off the recording.
● S
HOWVIEW Timer programming is not possible on the discs used
exclusively for On-Disc Timer programming.
● If the copy limited programme is received during timer-recording, the
unit enters Record Pause mode. Recording starts again if it is
switched to a recordable broadcast during the time you programmed.
Daily/Weekly Recording
You can record programmes with one of the following weekly/daily
timer settings.
WEEKLY: Select to record a weekly programme.
MON–FRI: Select to record a daily programme from Monday
through Friday.
MON–SAT: Select to record a daily programme from Monday
through Saturday.
SUN–SAT: Select to record a daily programme from Sunday
through Saturday.
SHOWVIEW
®
Timer Programming
● Make sure that the unit’s built-in clock is set properly.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
IMPORTANT:
Make sure the channel position number you wish to record is
displayed; if not, see “S
HOWVIEW
®
System Setup” (墌 pg. 82) and set
the Guide Program number correctly.
1
4
7
2
5
8
0
3
6
9
0 – 9
RETURN
ENTER
SHOWVIEW
CLEAR (8)
CANCEL (X)
DVD TIMER (#)
VCR/DVD
SAT
IMPORTANT:
If you have moved to a different area or if a broadcasting station's
channel number has been changed, the wrong channel number will
be displayed on the S
HOWVIEW programme screen in step 5. When
this happens, set the correct Guide Program number for that station.
(
墌 pg. 82, “SHOWVIEW
®
System Setup”)
Satellite Receiver Users
To timer-record a satellite broadcast using the S
HOWVIEW
system:
A Perform “Satellite Receiver Control Setting” (墌 pg. 21).
B Perform “S
HOWVIEW
®
Timer Programming” (墌 pg. 43).
C Leave the satellite receiver’s power on.
DR-MV1SE_00.book Page 43 Thursday, March 11, 2004 7:28 PM

JVC DR-MV1 Specifications

General

Brand	JVC
Model	DR-MV1
Category	DVD VCR Combo
Language	English