Kenwood 1090VR User Manual

le system control
soos as
aes
A
Connecting system control cords after connecting a KENWOOD audio component system lets you take advantage of
convenient system control operations.
There are two KENWOOD system control modes. Make connections according to the groups of terminal symbols shown
below.
X88 Made : lets you combine [XS XSB, and Xf terminals
(LTB) Mode : for (GLB) terminals only
This unit is compatible with both [XS8] and [SL16] modes. It comes from the factory set to the [SL16] mode. To switch to the [XS8] mode, follow
the instructions in “SWITCHING FROM [SL16] TO [XS8]” below.
EXAMPLE: [XS8] mode connections EXAMPLE: [SL16] mode connections
The underlined portion represents the setting of the system control mode. The underlined portion represents the setting of the system contro! mode
[SL16} (XSB) Receiver [SL16] IxS8]
[SL16] MD recorder [SL16} MD recorder
[SL16][XSI[XS8][XR] | Cassette deck 2onin5, [SL16] [XS] [X$8] [XR] Cassette deck | 25 GN,
[SL16]
[XS]
[X$8]
CD
player
so
[SL16]
[XS]
[XS8]
CD
player
-
[XS] Record player {X$] Record player
* In order to take advantage of the system control operations, the components must be connected to the correct jacks. To use a CD player it must
be connected to the CD jacks. To use a cassette deck (or MD recorder) it must be connected to the TAPE1/MD jacks. When using more than one
CD player (etc.) only the one connected to the specified jacks may be connected for system control.
¢ Some CD players and cassette decks are not compatible with the [SL16] system control mode Be sure to use the [XS8] system control mode
when making system connections with equipment that is not [SL16] compatible.
«Some MD players are not system control compatible. You cannot make system control connections to this kind of equipment.
1. [SL16] equipment cannot be combined with [XR], [XS], and {XS8] equipment for system operations. If your :
equipment consists of this kind of combination, please do not connect any system contro! cords. Even without Ne, gf
i system control cords, normal operations can be carried out without effecting performance. he — { [=
| (Notes) 2 Do not connect system control cords to any components other than those specified by KENWOOD. It may oe Py 4
cause a malfunction and damage your equipment. "es we
3. Be sure tne system control plugs are inserted all the way in to the system contro! terminals.
SYSTEM
CONTROL
OPERATIONS
SWITCHING
FROM
[SL16]
TO
[XS8]
Remote
Control
You
can
easily
change
the
system
contro!
mode
by
adjusting
the
S
yOu
operate
tis
unit
with
the
system
remote
supplied
with
the
position
of
the
SYSTEM
CONTROL
switch
on
the
rear
panel.
j;
recever
;
Do
this
operation
after
completing
all
connections.
Automatic
Operation
(except
[XR]
equipment)
JISL
16
For
{SL16]
When
you
Start
playback
from
a
source
component,
the
input
selector
on
tnis
unit
Switches
to
that
component
automatically
1XS
8
For
[xss]
Synchronized
Recording
(except
[XR]
equipment)
+
This
operation
will
not
effect
items
stored
in
the
memory.
Lets
vou
synchronize
recording
with the
start
of
piayback
when
+
After
switching
the
system
control
mode,
turn
the
power
off
and
i recoraina from CD. MD or anaiog discs then on once to confirm the new setting.
Registering setup codes for KENWOOD audio components
* Once you finish making the system connections, be sure to register the appropriate setup code for each component. = 38.
*
if
you
own
remote
contrcilable
KENWOOD
audio
components
that
are
not
compatible
with
system
control
(or
cannot
be
combined
with
your
other
system control
components},
registering the
setup
code
enables
you
to
control
those
components
using
the
remote
control
supplied with
this
unit
(without
connecting
system
contro!
cords).
To
register
setup
codes
for
your
remote
controllable
KENWOOD
audio
components,
see
“Registering
setup
codes
for
other
components’
-
38

Kenwood 1090VR Specifications

General

Brand	Kenwood
Model	1090VR
Category	Stereo Receiver
Language	English