Kenwood 1090VR User Manual

Setting up the system
1OSOVR (En /K)
Making connections to another room (ROOM B) |
The
following
connections
allow
you
to
connect
your
main
system
to
a
monitor
TV
and
speaker
system
located
in
another
area
(ROOM
B).
The
monitor
TV
can
be
connected
directly
to
the
SECOND
ROOM
PRE
OUT
VIDEO
jack.
To
connect
the
speakers,
use
either
of
the
connections described below.
To
select
the
input
and
adjust
the
voiume
(etc.)
for
your
other
area
(ROOM
B),
set
the
remote
control
to
the
ROOM
B
operation
mode.
FRONT SPEAKERS B connections (1 ):
These connections aliow you to connect the speakers in ROOM
B directly to the receiver without using an additional power
amplifier. The sound from the main system (ROOM A) automati-
cally switches to stereo when SPEAKERS B are turned on. ~_48.
Monitor TV
Speakers (.2:)
=
Power amp
i VIDEO pela SI ce
SECOND RGOM PRE OUT | ROOM PRE OUT |
re lan
© Oo
m~ AK
SS. Oey
: on
S Vu
i
ore
Shs
= — AA me
p= = oe 4a ope
S ore heuer WE
390 sii pat
8 | 33 BEst SIS erees:
at ta 4
tweed
|e
IR RELAY CONTROL ( 3}
REPEATER
1
RECIEVER
IN
(4)
QUT
(>)
The following connections are only available for models sold
in the U.S.A. and Canada.
RELAY CONTROL (2):
» Gesianed to operate external devices and 1s
™ tne Xantecn 599-00 Pulse Switching Module or
is Do not exceed maximum current by connecting
Multiple 539-00 modules. Please consult the owner's manual
of the external device for compatibility and installation
instructions before attempting connections to your new
receiver. Improper installation, or connection of non-com-
patible equipment, may damage this control output. Please
consult the dealer where the external equipment was pur-
chased or a competent installation specialist for more infor-
mation. ~_57
— 45.
SECOND ROOM PRE OUT connections (.2 ):
Use these connections if you want to enjoy surround sound from «
your main system (ROOM A) while outputting another source to ©
ROOM B. Connecting @ speaker cord directly to a SECOND |
ROOM PRE OUT jack will not produce any sound from the
speaker. Connect the SECOND ROOM PRE OUT jacks to_pow- .
ered speakers or power amplifiers connected to speakers. ;
A.
\
/
8
52:8)
;
/ ) ROOM A iI \
oof (Main System) \
IR RECEIVER IN (4):
This input lets you connect an external IR receiver to enable
remote control of this unit even if It is located in a cabinet or
behind glass doors (etc.). The external IR receiver works the
same as the IR receiver located on the front of this unit. This input
Is compatible with Xantech 291-80. 480-30, 490-30 and similar
models. — $1.
IR REPEATER OUT (5):
These outputs let you connect IR repeaters to contro! compo-
nents located in cabinets or behind glass doors (etc.). The
repeaters send out signals corresponding to those of the remote
control supplied with the respective equipment. These outputs
are compatible with Xantech 282-00. 286-00, 283-00 and similar
models. — 57.
The IR REPEATER OUT terminals may only used when an
external IR receiver is connected to the IR RECEIVER IN
terminal. ©

Kenwood 1090VR Specifications

General

Brand	Kenwood
Model	1090VR
Category	Stereo Receiver
Language	English