Kenwood 1090VR User Manual

g
Remote control unit
The backlight fiashes five times during nor-
mal operation.
Subwoofer volume cannot be adjusted.
Certain inputs cannot be selected using
the remote control.
The batteries are nearing exhaustion.
Subwoofer is OFF.
No preset codes registered at for the respec-
tive input(s).
Remote control operation is not possible.
For the U.S.A.
FCC WARNING
change or modification is, made.
NOTE: . é
~—Reorient or relocate the receiving antenna.
The remote control is set to a different opera-
tion mode.
Batteries are exhausted.
The remote control unit is too far away from
the main system, controlling angle is too large,
or there is an obstacle between the receiver
and the remote.
The audio cords and system contro! cords are
not connected properly.
No software is loaded in the source compo-
nent.
An attempt is made to play a tape which is
being recorded in the cassette deck.
The remote control has not been set to the
operation mode for the component you wish
to control.
The remote control is in the Room B (A)
operation mode.
— ~ Increase the separation between the equipment and receiver.
-~ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
~— Consult the dealer or an experienced radio / TV technician for help.
e Turn the subwoofer ON.
[ Memory back up function
the AC outlet for approximately 3 days.
* Power mode.
* Input selector settings.
«Volume level
¢ Broadcast band.
¢ Frequency setting.
* Preset stations.
Nos
Please note that the following items will be deleted from
the unit's memory if the power cord is disconnected from
* Settings made using OSD (like SURROUND SET UP).
For the U.S.A.
1OSOVR [En/K}
e Replace with new batteries to preserve the
currently registered setup information. ~ 16.
~ 18.
Register a preset code or Non-!R code at the
respective input(s). 38
Press VIDEO, AUDIO, or TV to select the
approriate operation mode.
Replace with new batteries. If the backup is
exhasted before you can replace the batter-
ies, redo the setup procedure.
Operate the remote control unit within the
controllabie range.
~ 26. - 3H
Connect properly referring to “Setting up the
system". s.
Place software in the source component you
want to play.
Wait until recording has completed.
Press the VIDEO, AUDIO, or TV key to activate
the operation mode for the component you
want to control before operation.
Change the operation mode. -(45-
— 41
Do
not
use
contact
cleaning
agents
because
they
could
cause
a
malfunction.
Be
specifically
careful
against
using
contact
cleaning
agents
containing oil,
since
they
may
deform
the
plastic components.
This
equipment
may
generate
or
use
radio
frequency
energy.
Changes
or
modifications
to
this
equipment
may
cause
harmful
interference
unless
the
modifications
are
expressly
approved
in
the
instruction
manual.
The
user
could
lose
the
authority
to
operate
this
equipment
if
an
unauthorized
This
equipment
has
been
tested
and
found
to
comply
with
the
limits
for
a
Class
B
digital
device,
pursuant
to
Part
15
of
the
FCC
Rules.
These
limits
are
designed
to
provide
reasonable
protection
against
harmful
interference
in
a
residential
installation.
This
equipment
may
cause
harmful
interference
to
radio
communications,
if
it
is
not
installed
and
used
in
accordance
with
the
instructions.
However,
there
is
no
guarantee
that
interference
will
not
occur
in
a
particular
installation.
If
this
equipment
does
cause
harmful
interference
to
radio
or
television
reception,
which
can
be
determined
by
turning
the
equipment
off
and
on,
the
user
is
encouraged
to
try
to
correct
the
interference
by
one
or
more
of
the
following
measures:
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s
attention to Article 820-40 of the NEC that provides guidelines for
proper grounding and, in particular, specifies that the cable ground
shalt be connected to the grounding system of the building, as close
to the point of cable entry as practical.

Kenwood 1090VR Specifications

General

Brand	Kenwood
Model	1090VR
Category	Stereo Receiver
Language	English