Kenwood DPX502 User Manual

English
|
17
Playing USB (iPod) device
When the USB device is not connected
Connect the USB device
Playback of the file contained in the USB device
starts.
When the USB device is connected
Select USB source
Press the [SRC] button.
Select the "USB" (or "iPod") display.
⁄
• For the audio files that can be played with this unit and
the devices that can be connected to this unit, refer to
<About Audio file> (page 5).
• The word "iPod" appearing in this manual indicates the
iPod connected with the KCA-iP200 (optional accessory).
Refer to <About Audio file> (page 5).
• If you start playback after connecting the iPod, the music
that has been played by the iPod is played first.
In this case, "RESUMING" is displayed without displaying
a folder name, etc. Changing the browse item will
display a correct title, etc.
• When the iPod is connected to this unit, "KENWOOD" or
"✓" is displayed on the iPod to indicate that you cannot
operate the iPod.
• When the USB device is connected to this unit, it can be
charged up provided that this unit is powered.
• When the Multi Card Reader is used, refer to <Drive
Search> (page 17).
• After you stopped playing a file contained in the USB
device, you can restart playing the file from the point
where you stopped its playback.
Even after removing the USB device, you can restart
playing the file from the point where you stopped its
playback as long as the files contained in the USB device
are all the same.
• Be sure to insert the USB device connector as far as it will
go.
• You can play the file made by KENWOOD Music Editor by
the same operation.
Pause and play
Press the Control knob.
Each time you press the knob, the audio pauses or
plays.
Removing the USB device
1 Set the remove mode as the USB source
Press the [0] button for at least 2 seconds.
"REMOVE" display blinks.
2 Remove the USB device.
Drive Search
Selecting the device inserted in the Multi Card
Reader.
1 Put the playback to pause
Press the [S.MODE] button.
2 Select a device
Push the Control knob towards up or down.
3 Restart playback
Press the [S.MODE] button.
⁄
• This unit is compliant with Multi Card Readers with a
maximum of 4 slots.
• If a device is inserted during connection of the Multi
Card Reader, it is not recognized. Select the Remove
mode with reference to <Playing USB (iPod) device>
(page 17), remove the Card Reader, and then insert the
memory.
B64-3826-0000English.Indd17B64-3826-0000English.Indd17 07.4.2411:32:10AM07.4.2411:32:10AM

Kenwood DPX502 Specifications

FM Tuner Section

frequency range	87.9 MHz – 107.9 MHz
usable sensitivity	9.3 dBf (0.8 μV /75 Ω)
quieting sensitivity	15.2 dBf (1.6 μV /75 Ω)
frequency response	30 Hz – 15 kHz
signal to noise ratio (MONO)	70 dB
selectivity	≥ 80 dB
stereo separation	40 dB

AM Tuner Section

frequency range	530 kHz – 1700 kHz
usable sensitivity	28 dBμ (25 μV)

CD Player Section

spindle speed	1000 – 400 rpm (CLV 2times)
frequency response	10 Hz – 20 kHz
total harmonic distortion	0.008 %
signal to noise ratio	105 dB
dynamic range	93 dB

Audio Output

maximum output power	50 W x 4
full bandwidth power	22 W x 4
speaker impedance	4 - 8 Ω
preout level / load	2500 mV/10 kΩ
preout impedance	≤ 600 Ω

USB Interface

usb standard	USB 1.1/ 2.0
maximum supply current	500 mA

Auxiliary Input

frequency response	20 Hz – 20 kHz
input maximum voltage	1200 mV
input impedance	100 kΩ

General Specifications

operating voltage	14.4 V
current consumption	10 A
installation size (W x H x D)	182 x 112 x 160 mm
weight	3.53 lbs (1.60 kg)