EasyManuals Logo

Kenwood DPX502 User Manual

Kenwood DPX502
40 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #3 background imageLoading...
Page #3 background image
English
|
3
2WARNING
To prevent injury or fire, take the following
precautions:
To prevent a short circuit, never put or leave any
metallic objects (such as coins or metal tools) inside
the unit.
Do not watch or fix your eyes on the units display
when you are driving for any extended period.
Mounting and wiring this product requires skills and
experience. For safetys sake, leave the mounting
and wiring work to professionals.
2CAUTION
To prevent damage to the machine, take
the following precautions:
Make sure to ground the unit to a negative 12V DC
power supply.
Do not install the unit in a spot exposed to direct
sunlight or excessive heat or humidity. Also avoid
places with too much dust or the possibility of
water splashing.
When replacing a fuse, only use a new fuse with
the prescribed rating. Using a fuse with the wrong
rating may cause your unit to malfunction.
Use only the screws provided or specified for
installation. If you use wrong screws, you could
damage the unit.
Do Not Load 3-in. CDs in the CD slot
If you try to load a 3 in. CD with its adapter into the
unit, the adapter might separate from the CD and
damage the unit.
About CD players/disc changers connected
to this unit
Kenwood disc changers/ CD players released in 1998
or later can be connected to this unit.
Refer to the catalog or consult your Kenwood dealer
for connectable models of disc changers/ CD players.
Note that any Kenwood disc changers/ CD players
released in 1997 or earlier and disc changers made by
other makers cannot be connected to this unit.
Connecting unsupported disc changers/CD players to
this unit may result in damage.
Set the "O-N" Switch to the "N" position for the
applicable Kenwood disc changers/ CD players.
The functions you can use and the information that
can be displayed may differ depending on the models
being connected.
¤
You can damage both your unit and the CD changer if you
connect them incorrectly.
Lens Fogging
When you turn on the car heater in cold weather,
dew or condensation may form on the lens in the
CD player of the unit. Called lens fogging, this
condensation on the lens may not allow CDs to play.
In such a situation, remove the disc and wait for the
condensation to evaporate. If the unit still does not
operate normally after a while, consult your Kenwood
dealer.
iPod is a trademark of Apple Inc., registered in
the U.S. and other countries.
The "AAC" logo is trademark of Dolby
Laboratories.
Safety precautions
B64-3826-0000English.Indd3B64-3826-0000English.Indd3 07.4.2411:32:05AM07.4.2411:32:05AM

Table of Contents

Other manuals for Kenwood DPX502

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Kenwood DPX502 and is the answer not in the manual?

Kenwood DPX502 Specifications

FM Tuner Section IconFM Tuner Section
frequency range87.9 MHz – 107.9 MHz
usable sensitivity9.3 dBf (0.8 μV /75 Ω)
quieting sensitivity15.2 dBf (1.6 μV /75 Ω)
frequency response30 Hz – 15 kHz
signal to noise ratio (MONO)70 dB
selectivity≥ 80 dB
stereo separation40 dB
AM Tuner Section IconAM Tuner Section
frequency range530 kHz – 1700 kHz
usable sensitivity28 dBμ (25 μV)
CD Player Section IconCD Player Section
spindle speed1000 – 400 rpm (CLV 2times)
frequency response10 Hz – 20 kHz
total harmonic distortion0.008 %
signal to noise ratio105 dB
dynamic range93 dB
Audio Output IconAudio Output
maximum output power50 W x 4
full bandwidth power22 W x 4
speaker impedance4 - 8 Ω
preout level / load2500 mV/10 kΩ
preout impedance≤ 600 Ω
USB Interface IconUSB Interface
usb standardUSB 1.1/ 2.0
maximum supply current500 mA
Auxiliary Input IconAuxiliary Input
frequency response20 Hz – 20 kHz
input maximum voltage1200 mV
input impedance100 kΩ
General Specifications IconGeneral Specifications
operating voltage14.4 V
current consumption10 A
installation size (W x H x D)182 x 112 x 160 mm
weight3.53 lbs (1.60 kg)

Related product manuals